�ݺ�ߣshows by User: DavidScaduto

�ݺ�ߣshows by User: DavidScaduto / http://www.slideshare.net/images/logo.gif �ݺ�ߣshows by User: DavidScaduto / Wed, 17 Aug 2016 16:04:13 GMT �ݺ�ߣShare feed for �ݺ�ߣshows by User: DavidScaduto Measuring Spatial Resolution in Digital Breast Tomosynthesis /slideshow/measuring-spatial-resolution-in-digital-breast-tomosynthesis/65092838 tg245aapm2016-160817160413
Purpose: Spatial resolution in digital breast tomosynthesis (DBT) is affected by inherent/binned detector resolution, oblique entry of x-rays, and focal spot size/motion; the limited angular range further limits spatial resolution in the depth-direction. While DBT is being widely adopted clinically, imaging performance metrics and quality control protocols have not been standardized. AAPM Task Group 245 on Tomosynthesis Quality Control has been formed to address this deficiency. Methods: Methods of measuring spatial resolution are evaluated using two prototype quality control phantoms for DBT. Spatial resolution in the detector plane is measured in projection and reconstruction domains using edge-spread function (ESF), point-spread function (PSF) and modulation transfer function (MTF). Spatial resolution in the depth-direction and effective slice thickness are measured in the reconstruction domain using slice sensitivity profile (SSP) and artifact spread function (ASF). An oversampled PSF in the depth-direction is measured using a 50 µm angulated tungsten wire, from which the MTF is computed. Object-dependent PSF is derived and compared with ASF. Sensitivity of these measurements to phantom positioning, imaging conditions and reconstruction algorithms is evaluated. Results are compared from systems of varying acquisition geometry (9-25 projections over 15-60°). Dependence of measurements on feature size is investigated. Results: Measurements of spatial resolution using PSF and LSF are shown to depend on feature size; depth-direction spatial resolution measurements are shown to similarly depend on feature size for ASF, though deconvolution with an object function removes feature size-dependence. A slanted wire may be used to measure oversampled PSFs, from which MTFs may be computed for both in-plane and depth-direction resolution. Conclusion: Spatial resolution measured using PSF is object-independent with sufficiently small object; MTF is object-independent. Depth-direction spatial resolution may be measured directly using MTF or indirectly using ASF or SSP as surrogate measurements. While MTF is object-independent, it is invalid for nonlinear reconstructions.]]>
Purpose: Spatial resolution in digital breast tomosynthesis (DBT) is affected by inherent/binned detector resolution, oblique entry of x-rays, and focal spot size/motion; the limited angular range further limits spatial resolution in the depth-direction. While DBT is being widely adopted clinically, imaging performance metrics and quality control protocols have not been standardized. AAPM Task Group 245 on Tomosynthesis Quality Control has been formed to address this deficiency. Methods: Methods of measuring spatial resolution are evaluated using two prototype quality control phantoms for DBT. Spatial resolution in the detector plane is measured in projection and reconstruction domains using edge-spread function (ESF), point-spread function (PSF) and modulation transfer function (MTF). Spatial resolution in the depth-direction and effective slice thickness are measured in the reconstruction domain using slice sensitivity profile (SSP) and artifact spread function (ASF). An oversampled PSF in the depth-direction is measured using a 50 µm angulated tungsten wire, from which the MTF is computed. Object-dependent PSF is derived and compared with ASF. Sensitivity of these measurements to phantom positioning, imaging conditions and reconstruction algorithms is evaluated. Results are compared from systems of varying acquisition geometry (9-25 projections over 15-60°). Dependence of measurements on feature size is investigated. Results: Measurements of spatial resolution using PSF and LSF are shown to depend on feature size; depth-direction spatial resolution measurements are shown to similarly depend on feature size for ASF, though deconvolution with an object function removes feature size-dependence. A slanted wire may be used to measure oversampled PSFs, from which MTFs may be computed for both in-plane and depth-direction resolution. Conclusion: Spatial resolution measured using PSF is object-independent with sufficiently small object; MTF is object-independent. Depth-direction spatial resolution may be measured directly using MTF or indirectly using ASF or SSP as surrogate measurements. While MTF is object-independent, it is invalid for nonlinear reconstructions.]]> Wed, 17 Aug 2016 16:04:13 GMT /slideshow/measuring-spatial-resolution-in-digital-breast-tomosynthesis/65092838 DavidScaduto@slideshare.net(DavidScaduto) Measuring Spatial Resolution in Digital Breast Tomosynthesis DavidScaduto Purpose: Spatial resolution in digital breast tomosynthesis (DBT) is affected by inherent/binned detector resolution, oblique entry of x-rays, and focal spot size/motion; the limited angular range further limits spatial resolution in the depth-direction. While DBT is being widely adopted clinically, imaging performance metrics and quality control protocols have not been standardized. AAPM Task Group 245 on Tomosynthesis Quality Control has been formed to address this deficiency. Methods: Methods of measuring spatial resolution are evaluated using two prototype quality control phantoms for DBT. Spatial resolution in the detector plane is measured in projection and reconstruction domains using edge-spread function (ESF), point-spread function (PSF) and modulation transfer function (MTF). Spatial resolution in the depth-direction and effective slice thickness are measured in the reconstruction domain using slice sensitivity profile (SSP) and artifact spread function (ASF). An oversampled PSF in the depth-direction is measured using a 50 µm angulated tungsten wire, from which the MTF is computed. Object-dependent PSF is derived and compared with ASF. Sensitivity of these measurements to phantom positioning, imaging conditions and reconstruction algorithms is evaluated. Results are compared from systems of varying acquisition geometry (9-25 projections over 15-60°). Dependence of measurements on feature size is investigated. Results: Measurements of spatial resolution using PSF and LSF are shown to depend on feature size; depth-direction spatial resolution measurements are shown to similarly depend on feature size for ASF, though deconvolution with an object function removes feature size-dependence. A slanted wire may be used to measure oversampled PSFs, from which MTFs may be computed for both in-plane and depth-direction resolution. Conclusion: Spatial resolution measured using PSF is object-independent with sufficiently small object; MTF is object-independent. Depth-direction spatial resolution may be measured directly using MTF or indirectly using ASF or SSP as surrogate measurements. While MTF is object-independent, it is invalid for nonlinear reconstructions. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/tg245aapm2016-160817160413-thumbnail.jpg?width=120&height=120&fit=bounds" /> Purpose: Spatial resolution in digital breast tomosynthesis (DBT) is affected by inherent/binned detector resolution, oblique entry of x-rays, and focal spot size/motion; the limited angular range further limits spatial resolution in the depth-direction. While DBT is being widely adopted clinically, imaging performance metrics and quality control protocols have not been standardized. AAPM Task Group 245 on Tomosynthesis Quality Control has been formed to address this deficiency. Methods: Methods of measuring spatial resolution are evaluated using two prototype quality control phantoms for DBT. Spatial resolution in the detector plane is measured in projection and reconstruction domains using edge-spread function (ESF), point-spread function (PSF) and modulation transfer function (MTF). Spatial resolution in the depth-direction and effective slice thickness are measured in the reconstruction domain using slice sensitivity profile (SSP) and artifact spread function (ASF). An oversampled PSF in the depth-direction is measured using a 50 µm angulated tungsten wire, from which the MTF is computed. Object-dependent PSF is derived and compared with ASF. Sensitivity of these measurements to phantom positioning, imaging conditions and reconstruction algorithms is evaluated. Results are compared from systems of varying acquisition geometry (9-25 projections over 15-60°). Dependence of measurements on feature size is investigated. Results: Measurements of spatial resolution using PSF and LSF are shown to depend on feature size; depth-direction spatial resolution measurements are shown to similarly depend on feature size for ASF, though deconvolution with an object function removes feature size-dependence. A slanted wire may be used to measure oversampled PSFs, from which MTFs may be computed for both in-plane and depth-direction resolution. Conclusion: Spatial resolution measured using PSF is object-independent with sufficiently small object; MTF is object-independent. Depth-direction spatial resolution may be measured directly using MTF or indirectly using ASF or SSP as surrogate measurements. While MTF is object-independent, it is invalid for nonlinear reconstructions.

Measuring Spatial Resolution in Digital Breast Tomosynthesis from David Scaduto

]]> 615 4 https://cdn.slidesharecdn.com/ss_thumbnails/tg245aapm2016-160817160413-thumbnail.jpg?width=120&height=120&fit=bounds presentation Black http://activitystrea.ms/schema/1.0/post

http://activitystrea.ms/schema/1.0/posted

0 Determination of System Geometrical Parameters and Consistency between Scans for Contrast-Enhanced Digital Breast Tomosynthesis /slideshow/determination-of-system-geometrical-parameters-and-consistency-between-scans-for-contrastenhanced-digital-breast-tomosynthesis/58562245 iwdmgeomcalibfinal-160222160047
Digital breast tomosynthesis (DBT) requires precise knowledge of acquisition geometry for accurate image reconstruction. Further, image subtraction techniques employed in dual-energy contrast-enhanced tomosynthesis require that scans be performed under nearly identical geometrical conditions. A geometrical calibration algorithm is developed to investigate system geometry and geometrical consistency of image acquisition between consecutive digital breast tomosynthesis scans, according to requirements for dual-energy contrast-enhanced tomosynthesis. Investigation of geometrical accuracy and consistency on a prototype DBT unit reveals accurate angular measurement, but potentially clinically significant differences in acquisition angles between scans. Further, a slight gantry wobble is observed, suggesting the need for incorporation of gantry wobble into image reconstruction, or improvements to system hardware.]]>
Digital breast tomosynthesis (DBT) requires precise knowledge of acquisition geometry for accurate image reconstruction. Further, image subtraction techniques employed in dual-energy contrast-enhanced tomosynthesis require that scans be performed under nearly identical geometrical conditions. A geometrical calibration algorithm is developed to investigate system geometry and geometrical consistency of image acquisition between consecutive digital breast tomosynthesis scans, according to requirements for dual-energy contrast-enhanced tomosynthesis. Investigation of geometrical accuracy and consistency on a prototype DBT unit reveals accurate angular measurement, but potentially clinically significant differences in acquisition angles between scans. Further, a slight gantry wobble is observed, suggesting the need for incorporation of gantry wobble into image reconstruction, or improvements to system hardware.]]> Mon, 22 Feb 2016 16:00:47 GMT /slideshow/determination-of-system-geometrical-parameters-and-consistency-between-scans-for-contrastenhanced-digital-breast-tomosynthesis/58562245 DavidScaduto@slideshare.net(DavidScaduto) Determination of System Geometrical Parameters and Consistency between Scans for Contrast-Enhanced Digital Breast Tomosynthesis DavidScaduto Digital breast tomosynthesis (DBT) requires precise knowledge of acquisition geometry for accurate image reconstruction. Further, image subtraction techniques employed in dual-energy contrast-enhanced tomosynthesis require that scans be performed under nearly identical geometrical conditions. A geometrical calibration algorithm is developed to investigate system geometry and geometrical consistency of image acquisition between consecutive digital breast tomosynthesis scans, according to requirements for dual-energy contrast-enhanced tomosynthesis. Investigation of geometrical accuracy and consistency on a prototype DBT unit reveals accurate angular measurement, but potentially clinically significant differences in acquisition angles between scans. Further, a slight gantry wobble is observed, suggesting the need for incorporation of gantry wobble into image reconstruction, or improvements to system hardware. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/iwdmgeomcalibfinal-160222160047-thumbnail.jpg?width=120&height=120&fit=bounds" /> Digital breast tomosynthesis (DBT) requires precise knowledge of acquisition geometry for accurate image reconstruction. Further, image subtraction techniques employed in dual-energy contrast-enhanced tomosynthesis require that scans be performed under nearly identical geometrical conditions. A geometrical calibration algorithm is developed to investigate system geometry and geometrical consistency of image acquisition between consecutive digital breast tomosynthesis scans, according to requirements for dual-energy contrast-enhanced tomosynthesis. Investigation of geometrical accuracy and consistency on a prototype DBT unit reveals accurate angular measurement, but potentially clinically significant differences in acquisition angles between scans. Further, a slight gantry wobble is observed, suggesting the need for incorporation of gantry wobble into image reconstruction, or improvements to system hardware.

Determination of System Geometrical Parameters and Consistency between Scans for Contrast-Enhanced Digital Breast Tomosynthesis from David Scaduto

]]> 409 4 https://cdn.slidesharecdn.com/ss_thumbnails/iwdmgeomcalibfinal-160222160047-thumbnail.jpg?width=120&height=120&fit=bounds presentation Black http://activitystrea.ms/schema/1.0/post

http://activitystrea.ms/schema/1.0/posted

0 Increasing Amorphous Selenium Thickness in Direct Conversion Flat-Panel Imagers for Contrast-Enhanced Dual-Energy Breast Imaging /slideshow/increasing-amorphous-selenium-thickness-in-direct-conversion-flatpanel-imagers-for-contrastenhanced-dualenergy-breast-imaging/58561855 aapm2014-160222155330
Purpose: Contrast-enhanced (CE) breast imaging using iodinated contrast agents requires imaging with x-ray spectra at energies greater than those used in mammography. Optimizing amorphous selenium (a-Se) flat panel imagers (FPI) for this higher energy range may increase lesion conspicuity. Methods: We compare imaging performance of a conventional FPI with 200 μm a-Se conversion layer to a prototype FPI with 300 μm a-Se layer. Both detectors are evaluated in a Siemens MAMMOMAT Inspiration prototype digital breast tomosynthesis (DBT) system using low-energy (W/Rh 28 kVp) and high-energy (W/Cu 49 kVp) x-ray spectra. Detectability of iodinated lesions in dual-energy images is evaluated using an iodine contrast phantom. Effects of beam obliquity are investigated in projection and reconstructed images using different reconstruction methods. The ideal observer signal-to-noise ratio is used as a figure-of-merit to predict the optimal a-Se thickness for CE lesion detectability without compromising conventional full-field digital mammography (FFDM) and DBT performance. Results: Increasing a-Se thickness from 200 μm to 300 μm preserves imaging performance at typical mammographic energies (e.g. W/Rh 28 kVp), and improves the detective quantum efficiency (DQE) for high energy (W/Cu 49 kVp) by 30%. While the more penetrating high-energy x-ray photons increase geometric blur due to beam obliquity in the FPI with thicker a-Se layer, the effect on lesion detectability in FBP reconstructions is negligible due to the reconstruction filters employed. Ideal observer SNR for CE objects shows improvements in in-plane detectability with increasing a-Se thicknesses, though small lesion detectability begins to degrade in oblique projections for a-Se thickness above 500 μm. Conclusion: Increasing a-Se thickness in direct conversion FPI from 200 μm to 300 μm improves lesion detectability in CE breast imaging with virtually no cost to conventional FFDM and DBT. This work was partially supported by a research grant from Siemens Healthcare.]]>
Purpose: Contrast-enhanced (CE) breast imaging using iodinated contrast agents requires imaging with x-ray spectra at energies greater than those used in mammography. Optimizing amorphous selenium (a-Se) flat panel imagers (FPI) for this higher energy range may increase lesion conspicuity. Methods: We compare imaging performance of a conventional FPI with 200 μm a-Se conversion layer to a prototype FPI with 300 μm a-Se layer. Both detectors are evaluated in a Siemens MAMMOMAT Inspiration prototype digital breast tomosynthesis (DBT) system using low-energy (W/Rh 28 kVp) and high-energy (W/Cu 49 kVp) x-ray spectra. Detectability of iodinated lesions in dual-energy images is evaluated using an iodine contrast phantom. Effects of beam obliquity are investigated in projection and reconstructed images using different reconstruction methods. The ideal observer signal-to-noise ratio is used as a figure-of-merit to predict the optimal a-Se thickness for CE lesion detectability without compromising conventional full-field digital mammography (FFDM) and DBT performance. Results: Increasing a-Se thickness from 200 μm to 300 μm preserves imaging performance at typical mammographic energies (e.g. W/Rh 28 kVp), and improves the detective quantum efficiency (DQE) for high energy (W/Cu 49 kVp) by 30%. While the more penetrating high-energy x-ray photons increase geometric blur due to beam obliquity in the FPI with thicker a-Se layer, the effect on lesion detectability in FBP reconstructions is negligible due to the reconstruction filters employed. Ideal observer SNR for CE objects shows improvements in in-plane detectability with increasing a-Se thicknesses, though small lesion detectability begins to degrade in oblique projections for a-Se thickness above 500 μm. Conclusion: Increasing a-Se thickness in direct conversion FPI from 200 μm to 300 μm improves lesion detectability in CE breast imaging with virtually no cost to conventional FFDM and DBT. This work was partially supported by a research grant from Siemens Healthcare.]]> Mon, 22 Feb 2016 15:53:29 GMT /slideshow/increasing-amorphous-selenium-thickness-in-direct-conversion-flatpanel-imagers-for-contrastenhanced-dualenergy-breast-imaging/58561855 DavidScaduto@slideshare.net(DavidScaduto) Increasing Amorphous Selenium Thickness in Direct Conversion Flat-Panel Imagers for Contrast-Enhanced Dual-Energy Breast Imaging DavidScaduto Purpose: Contrast-enhanced (CE) breast imaging using iodinated contrast agents requires imaging with x-ray spectra at energies greater than those used in mammography. Optimizing amorphous selenium (a-Se) flat panel imagers (FPI) for this higher energy range may increase lesion conspicuity. Methods: We compare imaging performance of a conventional FPI with 200 μm a-Se conversion layer to a prototype FPI with 300 μm a-Se layer. Both detectors are evaluated in a Siemens MAMMOMAT Inspiration prototype digital breast tomosynthesis (DBT) system using low-energy (W/Rh 28 kVp) and high-energy (W/Cu 49 kVp) x-ray spectra. Detectability of iodinated lesions in dual-energy images is evaluated using an iodine contrast phantom. Effects of beam obliquity are investigated in projection and reconstructed images using different reconstruction methods. The ideal observer signal-to-noise ratio is used as a figure-of-merit to predict the optimal a-Se thickness for CE lesion detectability without compromising conventional full-field digital mammography (FFDM) and DBT performance. Results: Increasing a-Se thickness from 200 μm to 300 μm preserves imaging performance at typical mammographic energies (e.g. W/Rh 28 kVp), and improves the detective quantum efficiency (DQE) for high energy (W/Cu 49 kVp) by 30%. While the more penetrating high-energy x-ray photons increase geometric blur due to beam obliquity in the FPI with thicker a-Se layer, the effect on lesion detectability in FBP reconstructions is negligible due to the reconstruction filters employed. Ideal observer SNR for CE objects shows improvements in in-plane detectability with increasing a-Se thicknesses, though small lesion detectability begins to degrade in oblique projections for a-Se thickness above 500 μm. Conclusion: Increasing a-Se thickness in direct conversion FPI from 200 μm to 300 μm improves lesion detectability in CE breast imaging with virtually no cost to conventional FFDM and DBT. This work was partially supported by a research grant from Siemens Healthcare. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/aapm2014-160222155330-thumbnail.jpg?width=120&height=120&fit=bounds" /> Purpose: Contrast-enhanced (CE) breast imaging using iodinated contrast agents requires imaging with x-ray spectra at energies greater than those used in mammography. Optimizing amorphous selenium (a-Se) flat panel imagers (FPI) for this higher energy range may increase lesion conspicuity. Methods: We compare imaging performance of a conventional FPI with 200 μm a-Se conversion layer to a prototype FPI with 300 μm a-Se layer. Both detectors are evaluated in a Siemens MAMMOMAT Inspiration prototype digital breast tomosynthesis (DBT) system using low-energy (W/Rh 28 kVp) and high-energy (W/Cu 49 kVp) x-ray spectra. Detectability of iodinated lesions in dual-energy images is evaluated using an iodine contrast phantom. Effects of beam obliquity are investigated in projection and reconstructed images using different reconstruction methods. The ideal observer signal-to-noise ratio is used as a figure-of-merit to predict the optimal a-Se thickness for CE lesion detectability without compromising conventional full-field digital mammography (FFDM) and DBT performance. Results: Increasing a-Se thickness from 200 μm to 300 μm preserves imaging performance at typical mammographic energies (e.g. W/Rh 28 kVp), and improves the detective quantum efficiency (DQE) for high energy (W/Cu 49 kVp) by 30%. While the more penetrating high-energy x-ray photons increase geometric blur due to beam obliquity in the FPI with thicker a-Se layer, the effect on lesion detectability in FBP reconstructions is negligible due to the reconstruction filters employed. Ideal observer SNR for CE objects shows improvements in in-plane detectability with increasing a-Se thicknesses, though small lesion detectability begins to degrade in oblique projections for a-Se thickness above 500 μm. Conclusion: Increasing a-Se thickness in direct conversion FPI from 200 μm to 300 μm improves lesion detectability in CE breast imaging with virtually no cost to conventional FFDM and DBT. This work was partially supported by a research grant from Siemens Healthcare.

Increasing Amorphous Selenium Thickness in Direct Conversion Flat-Panel Imagers for Contrast-Enhanced Dual-Energy Breast Imaging from David Scaduto

]]> 551 8 https://cdn.slidesharecdn.com/ss_thumbnails/aapm2014-160222155330-thumbnail.jpg?width=120&height=120&fit=bounds presentation Black http://activitystrea.ms/schema/1.0/post

http://activitystrea.ms/schema/1.0/posted

0 Investigation of spatial resolution and temporal performance of SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout) with integrated electrostatic focusing /slideshow/investigation-of-spatial-resolution-and-temporal-performance-of-saphire-scintillator-avalanche-photoconductor-with-high-resolution-emitter-readout-with-integrated-electrostatic-focusing/58560784 spiesaphirepostervfin-160222153251
We have previously proposed SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout), a novel detector concept with potentially superior spatial resolution and low-dose performance compared with existing flat-panel imagers. The detector comprises a scintillator that is optically coupled to an amorphous selenium photoconductor operated with avalanche gain, known as high-gain avalanche rushing photoconductor (HARP). High resolution electron beam readout is achieved using a field emitter array (FEA). This combination of avalanche gain, allowing for very low-dose imaging, and electron emitter readout, providing high spatial resolution, offers potentially superior image quality compared with existing flat-panel imagers, with specific applications to fluoroscopy and breast imaging. Through the present collaboration, a prototype HARP sensor with integrated electrostatic focusing and nano- Spindt FEA readout technology has been fabricated. The integrated electron-optic focusing approach is more suitable for fabricating large-area detectors. We investigate the dependence of spatial resolution on sensor structure and operating conditions, and compare the performance of electrostatic focusing with previous technologies. Our results show a clear dependence of spatial resolution on electrostatic focusing potential, with performance approaching that of the previous design with external mesh-electrode. Further, temporal performance (lag) of the detector is evaluated and the results show that the integrated electrostatic focusing design exhibits comparable or better performance compared with the mesh-electrode design. This study represents the first technical evaluation and characterization of the SAPHIRE concept with integrated electrostatic focusing.]]>
We have previously proposed SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout), a novel detector concept with potentially superior spatial resolution and low-dose performance compared with existing flat-panel imagers. The detector comprises a scintillator that is optically coupled to an amorphous selenium photoconductor operated with avalanche gain, known as high-gain avalanche rushing photoconductor (HARP). High resolution electron beam readout is achieved using a field emitter array (FEA). This combination of avalanche gain, allowing for very low-dose imaging, and electron emitter readout, providing high spatial resolution, offers potentially superior image quality compared with existing flat-panel imagers, with specific applications to fluoroscopy and breast imaging. Through the present collaboration, a prototype HARP sensor with integrated electrostatic focusing and nano- Spindt FEA readout technology has been fabricated. The integrated electron-optic focusing approach is more suitable for fabricating large-area detectors. We investigate the dependence of spatial resolution on sensor structure and operating conditions, and compare the performance of electrostatic focusing with previous technologies. Our results show a clear dependence of spatial resolution on electrostatic focusing potential, with performance approaching that of the previous design with external mesh-electrode. Further, temporal performance (lag) of the detector is evaluated and the results show that the integrated electrostatic focusing design exhibits comparable or better performance compared with the mesh-electrode design. This study represents the first technical evaluation and characterization of the SAPHIRE concept with integrated electrostatic focusing.]]> Mon, 22 Feb 2016 15:32:51 GMT /slideshow/investigation-of-spatial-resolution-and-temporal-performance-of-saphire-scintillator-avalanche-photoconductor-with-high-resolution-emitter-readout-with-integrated-electrostatic-focusing/58560784 DavidScaduto@slideshare.net(DavidScaduto) Investigation of spatial resolution and temporal performance of SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout) with integrated electrostatic focusing DavidScaduto We have previously proposed SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout), a novel detector concept with potentially superior spatial resolution and low-dose performance compared with existing flat-panel imagers. The detector comprises a scintillator that is optically coupled to an amorphous selenium photoconductor operated with avalanche gain, known as high-gain avalanche rushing photoconductor (HARP). High resolution electron beam readout is achieved using a field emitter array (FEA). This combination of avalanche gain, allowing for very low-dose imaging, and electron emitter readout, providing high spatial resolution, offers potentially superior image quality compared with existing flat-panel imagers, with specific applications to fluoroscopy and breast imaging. Through the present collaboration, a prototype HARP sensor with integrated electrostatic focusing and nano- Spindt FEA readout technology has been fabricated. The integrated electron-optic focusing approach is more suitable for fabricating large-area detectors. We investigate the dependence of spatial resolution on sensor structure and operating conditions, and compare the performance of electrostatic focusing with previous technologies. Our results show a clear dependence of spatial resolution on electrostatic focusing potential, with performance approaching that of the previous design with external mesh-electrode. Further, temporal performance (lag) of the detector is evaluated and the results show that the integrated electrostatic focusing design exhibits comparable or better performance compared with the mesh-electrode design. This study represents the first technical evaluation and characterization of the SAPHIRE concept with integrated electrostatic focusing. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/spiesaphirepostervfin-160222153251-thumbnail.jpg?width=120&height=120&fit=bounds" /> We have previously proposed SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout), a novel detector concept with potentially superior spatial resolution and low-dose performance compared with existing flat-panel imagers. The detector comprises a scintillator that is optically coupled to an amorphous selenium photoconductor operated with avalanche gain, known as high-gain avalanche rushing photoconductor (HARP). High resolution electron beam readout is achieved using a field emitter array (FEA). This combination of avalanche gain, allowing for very low-dose imaging, and electron emitter readout, providing high spatial resolution, offers potentially superior image quality compared with existing flat-panel imagers, with specific applications to fluoroscopy and breast imaging. Through the present collaboration, a prototype HARP sensor with integrated electrostatic focusing and nano- Spindt FEA readout technology has been fabricated. The integrated electron-optic focusing approach is more suitable for fabricating large-area detectors. We investigate the dependence of spatial resolution on sensor structure and operating conditions, and compare the performance of electrostatic focusing with previous technologies. Our results show a clear dependence of spatial resolution on electrostatic focusing potential, with performance approaching that of the previous design with external mesh-electrode. Further, temporal performance (lag) of the detector is evaluated and the results show that the integrated electrostatic focusing design exhibits comparable or better performance compared with the mesh-electrode design. This study represents the first technical evaluation and characterization of the SAPHIRE concept with integrated electrostatic focusing.

Investigation of spatial resolution and temporal performance of SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout) with integrated electrostatic focusing from David Scaduto

]]> 334 6 https://cdn.slidesharecdn.com/ss_thumbnails/spiesaphirepostervfin-160222153251-thumbnail.jpg?width=120&height=120&fit=bounds presentation Black http://activitystrea.ms/schema/1.0/post

http://activitystrea.ms/schema/1.0/posted

0 Digital Breast Tomosynthesis with Minimal Compression /slideshow/digital-breast-tomosynthesis-with-minimal-compression/58558676 spiemincomp-160222145154
Breast compression is utilized in mammography to improve image quality and reduce radiation dose. Lesion conspicuity is improved by reducing scatter effects on contrast and by reducing the superposition of tissue structures. However, patient discomfort due to breast compression has been cited as a potential cause of noncompliance with recommended screening practices. Further, compression may also occlude blood flow in the breast, complicating imaging with intravenous contrast agents and preventing accurate quantification of contrast enhancement and kinetics. Previous studies have investigated reducing breast compression in planar mammography and digital breast tomosynthesis (DBT), though this typically comes at the expense of degradation in image quality or increase in mean glandular dose (MGD). We propose to optimize the image acquisition technique for reduced compression in DBT without compromising image quality or increasing MGD. A zero-frequency signal-difference-to-noise ratio model is employed to investigate the relationship between tube potential, SDNR and MGD. Phantom and patient images are acquired on a prototype DBT system using the optimized imaging parameters and are assessed for image quality and lesion conspicuity. A preliminary assessment of patient motion during DBT with minimal compression is presented.]]>
Breast compression is utilized in mammography to improve image quality and reduce radiation dose. Lesion conspicuity is improved by reducing scatter effects on contrast and by reducing the superposition of tissue structures. However, patient discomfort due to breast compression has been cited as a potential cause of noncompliance with recommended screening practices. Further, compression may also occlude blood flow in the breast, complicating imaging with intravenous contrast agents and preventing accurate quantification of contrast enhancement and kinetics. Previous studies have investigated reducing breast compression in planar mammography and digital breast tomosynthesis (DBT), though this typically comes at the expense of degradation in image quality or increase in mean glandular dose (MGD). We propose to optimize the image acquisition technique for reduced compression in DBT without compromising image quality or increasing MGD. A zero-frequency signal-difference-to-noise ratio model is employed to investigate the relationship between tube potential, SDNR and MGD. Phantom and patient images are acquired on a prototype DBT system using the optimized imaging parameters and are assessed for image quality and lesion conspicuity. A preliminary assessment of patient motion during DBT with minimal compression is presented.]]> Mon, 22 Feb 2016 14:51:54 GMT /slideshow/digital-breast-tomosynthesis-with-minimal-compression/58558676 DavidScaduto@slideshare.net(DavidScaduto) Digital Breast Tomosynthesis with Minimal Compression DavidScaduto Breast compression is utilized in mammography to improve image quality and reduce radiation dose. Lesion conspicuity is improved by reducing scatter effects on contrast and by reducing the superposition of tissue structures. However, patient discomfort due to breast compression has been cited as a potential cause of noncompliance with recommended screening practices. Further, compression may also occlude blood flow in the breast, complicating imaging with intravenous contrast agents and preventing accurate quantification of contrast enhancement and kinetics. Previous studies have investigated reducing breast compression in planar mammography and digital breast tomosynthesis (DBT), though this typically comes at the expense of degradation in image quality or increase in mean glandular dose (MGD). We propose to optimize the image acquisition technique for reduced compression in DBT without compromising image quality or increasing MGD. A zero-frequency signal-difference-to-noise ratio model is employed to investigate the relationship between tube potential, SDNR and MGD. Phantom and patient images are acquired on a prototype DBT system using the optimized imaging parameters and are assessed for image quality and lesion conspicuity. A preliminary assessment of patient motion during DBT with minimal compression is presented. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/spiemincomp-160222145154-thumbnail.jpg?width=120&height=120&fit=bounds" /> Breast compression is utilized in mammography to improve image quality and reduce radiation dose. Lesion conspicuity is improved by reducing scatter effects on contrast and by reducing the superposition of tissue structures. However, patient discomfort due to breast compression has been cited as a potential cause of noncompliance with recommended screening practices. Further, compression may also occlude blood flow in the breast, complicating imaging with intravenous contrast agents and preventing accurate quantification of contrast enhancement and kinetics. Previous studies have investigated reducing breast compression in planar mammography and digital breast tomosynthesis (DBT), though this typically comes at the expense of degradation in image quality or increase in mean glandular dose (MGD). We propose to optimize the image acquisition technique for reduced compression in DBT without compromising image quality or increasing MGD. A zero-frequency signal-difference-to-noise ratio model is employed to investigate the relationship between tube potential, SDNR and MGD. Phantom and patient images are acquired on a prototype DBT system using the optimized imaging parameters and are assessed for image quality and lesion conspicuity. A preliminary assessment of patient motion during DBT with minimal compression is presented.

Digital Breast Tomosynthesis with Minimal Compression from David Scaduto

]]> 1310 13 https://cdn.slidesharecdn.com/ss_thumbnails/spiemincomp-160222145154-thumbnail.jpg?width=120&height=120&fit=bounds presentation Black http://activitystrea.ms/schema/1.0/post

http://activitystrea.ms/schema/1.0/posted

0 https://public.slidesharecdn.com/v2/images/profile-picture.png https://cdn.slidesharecdn.com/ss_thumbnails/tg245aapm2016-160817160413-thumbnail.jpg?width=320&height=320&fit=bounds slideshow/measuring-spatial-resolution-in-digital-breast-tomosynthesis/65092838 Measuring Spatial Reso... https://cdn.slidesharecdn.com/ss_thumbnails/iwdmgeomcalibfinal-160222160047-thumbnail.jpg?width=320&height=320&fit=bounds slideshow/determination-of-system-geometrical-parameters-and-consistency-between-scans-for-contrastenhanced-digital-breast-tomosynthesis/58562245 Determination of Syste... https://cdn.slidesharecdn.com/ss_thumbnails/aapm2014-160222155330-thumbnail.jpg?width=320&height=320&fit=bounds slideshow/increasing-amorphous-selenium-thickness-in-direct-conversion-flatpanel-imagers-for-contrastenhanced-dualenergy-breast-imaging/58561855 Increasing Amorphous S...