ºÝºÝߣshows by User: ManalAbdullatif / http://www.slideshare.net/images/logo.gif ºÝºÝߣshows by User: ManalAbdullatif / Wed, 12 Jun 2019 08:35:46 GMT ºÝºÝߣShare feed for ºÝºÝߣshows by User: ManalAbdullatif Wear Properties of Thixoformed Al-5.7Si-2Cu-0.3Mg Aluminium Alloy /slideshow/wear-properties-of-thixoformed-al57si2cu03mg-aluminium-alloy/149289571 mysecondpapers2ppaper-190612083546
Earlier work has shown that Al-5.7Si-2Cu-0.3Mg aluminium alloy is suitable for thixoforming process. Here, the dry sliding wear behaviour of the alloy, in the as-cast and thixoformed conditions were investigated. The cooling slope technique was used to produce the alloy with globular microstructure for the thixoforming process. Both the thixoformed and cast samples were subjected to T6 heat treatments prior to the wear tests. The tests were carried out using a pin-on-disc tribometer, against a hardened M2 tool steel disc of 62 HRC at different loads, under dry sliding conditions at fixed sliding speed and sliding distance of 1 m.s–1 and 5 km respectively. The microstructural response, worn surfaces was thoroughly and carefully examined using various methods such as scanning electron microscopy, energy dispersive spectroscopy, and differential scanning calorimetry. The density of the heat treated thixoformed alloys showed significant increase in the hardness property, among others, due to its reduced porosity. Their wear test results also observed that the weight loss of materials increase with an increase in the input load and the sliding distance for all samples. However, the as-cast alloy displayed higher wear rate compared with the thixoformed alloys. In general, the wear mechanisms showed a mixture of abrasive, oxidative and delamination wear (mild wear) at low applied loads and mainly an adhesive (severe wear) at high applied loads.]]>
Earlier work has shown that Al-5.7Si-2Cu-0.3Mg aluminium alloy is suitable for thixoforming process. Here, the dry sliding wear behaviour of the alloy, in the as-cast and thixoformed conditions were investigated. The cooling slope technique was used to produce the alloy with globular microstructure for the thixoforming process. Both the thixoformed and cast samples were subjected to T6 heat treatments prior to the wear tests. The tests were carried out using a pin-on-disc tribometer, against a hardened M2 tool steel disc of 62 HRC at different loads, under dry sliding conditions at fixed sliding speed and sliding distance of 1 m.s–1 and 5 km respectively. The microstructural response, worn surfaces was thoroughly and carefully examined using various methods such as scanning electron microscopy, energy dispersive spectroscopy, and differential scanning calorimetry. The density of the heat treated thixoformed alloys showed significant increase in the hardness property, among others, due to its reduced porosity. Their wear test results also observed that the weight loss of materials increase with an increase in the input load and the sliding distance for all samples. However, the as-cast alloy displayed higher wear rate compared with the thixoformed alloys. In general, the wear mechanisms showed a mixture of abrasive, oxidative and delamination wear (mild wear) at low applied loads and mainly an adhesive (severe wear) at high applied loads.]]> Wed, 12 Jun 2019 08:35:46 GMT /slideshow/wear-properties-of-thixoformed-al57si2cu03mg-aluminium-alloy/149289571 ManalAbdullatif@slideshare.net(ManalAbdullatif) Wear Properties of Thixoformed Al-5.7Si-2Cu-0.3Mg Aluminium Alloy ManalAbdullatif Earlier work has shown that Al-5.7Si-2Cu-0.3Mg aluminium alloy is suitable for thixoforming process. Here, the dry sliding wear behaviour of the alloy, in the as-cast and thixoformed conditions were investigated. The cooling slope technique was used to produce the alloy with globular microstructure for the thixoforming process. Both the thixoformed and cast samples were subjected to T6 heat treatments prior to the wear tests. The tests were carried out using a pin-on-disc tribometer, against a hardened M2 tool steel disc of 62 HRC at different loads, under dry sliding conditions at fixed sliding speed and sliding distance of 1 m.s–1 and 5 km respectively. The microstructural response, worn surfaces was thoroughly and carefully examined using various methods such as scanning electron microscopy, energy dispersive spectroscopy, and differential scanning calorimetry. The density of the heat treated thixoformed alloys showed significant increase in the hardness property, among others, due to its reduced porosity. Their wear test results also observed that the weight loss of materials increase with an increase in the input load and the sliding distance for all samples. However, the as-cast alloy displayed higher wear rate compared with the thixoformed alloys. In general, the wear mechanisms showed a mixture of abrasive, oxidative and delamination wear (mild wear) at low applied loads and mainly an adhesive (severe wear) at high applied loads. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/mysecondpapers2ppaper-190612083546-thumbnail.jpg?width=120&amp;height=120&amp;fit=bounds" /><br> Earlier work has shown that Al-5.7Si-2Cu-0.3Mg aluminium alloy is suitable for thixoforming process. Here, the dry sliding wear behaviour of the alloy, in the as-cast and thixoformed conditions were investigated. The cooling slope technique was used to produce the alloy with globular microstructure for the thixoforming process. Both the thixoformed and cast samples were subjected to T6 heat treatments prior to the wear tests. The tests were carried out using a pin-on-disc tribometer, against a hardened M2 tool steel disc of 62 HRC at different loads, under dry sliding conditions at fixed sliding speed and sliding distance of 1 m.s–1 and 5 km respectively. The microstructural response, worn surfaces was thoroughly and carefully examined using various methods such as scanning electron microscopy, energy dispersive spectroscopy, and differential scanning calorimetry. The density of the heat treated thixoformed alloys showed significant increase in the hardness property, among others, due to its reduced porosity. Their wear test results also observed that the weight loss of materials increase with an increase in the input load and the sliding distance for all samples. However, the as-cast alloy displayed higher wear rate compared with the thixoformed alloys. In general, the wear mechanisms showed a mixture of abrasive, oxidative and delamination wear (mild wear) at low applied loads and mainly an adhesive (severe wear) at high applied loads.
Wear Properties of Thixoformed Al-5.7Si-2Cu-0.3Mg Aluminium Alloy from Dr. Manal Abdullatif
]]> 64 1 https://cdn.slidesharecdn.com/ss_thumbnails/mysecondpapers2ppaper-190612083546-thumbnail.jpg?width=120&height=120&fit=bounds document Black http://activitystrea.ms/schema/1.0/post http://activitystrea.ms/schema/1.0/posted 0 Dry Sliding Wear Behaviour of Rheocat Al-5.7Si-2Cu-0.3Mg Alloy /slideshow/d-ry-sliding-wear-behaviour-o-f-rheocat-al-57si-2cu-03mg-a-l-l-oy/149289516 my1stpapaer-190612083412
In this study, the effect of improved microstructure of Al-5.7Si-2Cu-0.3Mg alloys by using semisolid process on hardness and dry sliding wear behaviour were investigated. The microstructures of conventional cast alloy were totally dendritic, while in rheocasting the dendrit-ic transfer to fine globular microstructures after using cooling slope casting. Tribological tests were carried out by using a pin-on-disc apparatus in dry sliding conditions. Wear tests were at low sliding speed 1ms-1 ,applied load at 50N and three different sliding distance (i.e., 1.8Km, 5.4Km and 9Km) respectively. An optical microscope and a scanning electron microscope were used to examine the micro-structure and to understand the wear mechanism on the worn surface of both samples. The results showed that, the wear resistance of rheocast alloy was improved and higher than that those produce by conventional casting. The volume loss of rheocast alloy show reduc-tion more than 18% at 1.8Km and 10% at 9Km compared to as-cast alloy. Moderate wear regimes were appeared in both alloys, accord-ing to the range of wear rate. The friction coefficient had increased due to increase in the contact point between pin and disc materials. The dominant wear mechanism for conventional and rheocasting alloys was adhesion wear and abrasive wear respectively.]]>
In this study, the effect of improved microstructure of Al-5.7Si-2Cu-0.3Mg alloys by using semisolid process on hardness and dry sliding wear behaviour were investigated. The microstructures of conventional cast alloy were totally dendritic, while in rheocasting the dendrit-ic transfer to fine globular microstructures after using cooling slope casting. Tribological tests were carried out by using a pin-on-disc apparatus in dry sliding conditions. Wear tests were at low sliding speed 1ms-1 ,applied load at 50N and three different sliding distance (i.e., 1.8Km, 5.4Km and 9Km) respectively. An optical microscope and a scanning electron microscope were used to examine the micro-structure and to understand the wear mechanism on the worn surface of both samples. The results showed that, the wear resistance of rheocast alloy was improved and higher than that those produce by conventional casting. The volume loss of rheocast alloy show reduc-tion more than 18% at 1.8Km and 10% at 9Km compared to as-cast alloy. Moderate wear regimes were appeared in both alloys, accord-ing to the range of wear rate. The friction coefficient had increased due to increase in the contact point between pin and disc materials. The dominant wear mechanism for conventional and rheocasting alloys was adhesion wear and abrasive wear respectively.]]> Wed, 12 Jun 2019 08:34:12 GMT /slideshow/d-ry-sliding-wear-behaviour-o-f-rheocat-al-57si-2cu-03mg-a-l-l-oy/149289516 ManalAbdullatif@slideshare.net(ManalAbdullatif) Dry Sliding Wear Behaviour of Rheocat Al-5.7Si-2Cu-0.3Mg Alloy ManalAbdullatif In this study, the effect of improved microstructure of Al-5.7Si-2Cu-0.3Mg alloys by using semisolid process on hardness and dry sliding wear behaviour were investigated. The microstructures of conventional cast alloy were totally dendritic, while in rheocasting the dendrit-ic transfer to fine globular microstructures after using cooling slope casting. Tribological tests were carried out by using a pin-on-disc apparatus in dry sliding conditions. Wear tests were at low sliding speed 1ms-1 ,applied load at 50N and three different sliding distance (i.e., 1.8Km, 5.4Km and 9Km) respectively. An optical microscope and a scanning electron microscope were used to examine the micro-structure and to understand the wear mechanism on the worn surface of both samples. The results showed that, the wear resistance of rheocast alloy was improved and higher than that those produce by conventional casting. The volume loss of rheocast alloy show reduc-tion more than 18% at 1.8Km and 10% at 9Km compared to as-cast alloy. Moderate wear regimes were appeared in both alloys, accord-ing to the range of wear rate. The friction coefficient had increased due to increase in the contact point between pin and disc materials. The dominant wear mechanism for conventional and rheocasting alloys was adhesion wear and abrasive wear respectively. <img style="border:1px solid #C3E6D8;float:right;" alt="" src="https://cdn.slidesharecdn.com/ss_thumbnails/my1stpapaer-190612083412-thumbnail.jpg?width=120&amp;height=120&amp;fit=bounds" /><br> In this study, the effect of improved microstructure of Al-5.7Si-2Cu-0.3Mg alloys by using semisolid process on hardness and dry sliding wear behaviour were investigated. The microstructures of conventional cast alloy were totally dendritic, while in rheocasting the dendrit-ic transfer to fine globular microstructures after using cooling slope casting. Tribological tests were carried out by using a pin-on-disc apparatus in dry sliding conditions. Wear tests were at low sliding speed 1ms-1 ,applied load at 50N and three different sliding distance (i.e., 1.8Km, 5.4Km and 9Km) respectively. An optical microscope and a scanning electron microscope were used to examine the micro-structure and to understand the wear mechanism on the worn surface of both samples. The results showed that, the wear resistance of rheocast alloy was improved and higher than that those produce by conventional casting. The volume loss of rheocast alloy show reduc-tion more than 18% at 1.8Km and 10% at 9Km compared to as-cast alloy. Moderate wear regimes were appeared in both alloys, accord-ing to the range of wear rate. The friction coefficient had increased due to increase in the contact point between pin and disc materials. The dominant wear mechanism for conventional and rheocasting alloys was adhesion wear and abrasive wear respectively.
Dry Sliding Wear Behaviour of Rheocat Al-5.7Si-2Cu-0.3Mg Alloy from Dr. Manal Abdullatif
]]> 55 1 https://cdn.slidesharecdn.com/ss_thumbnails/my1stpapaer-190612083412-thumbnail.jpg?width=120&height=120&fit=bounds document Black http://activitystrea.ms/schema/1.0/post http://activitystrea.ms/schema/1.0/posted 0 https://public.slidesharecdn.com/v2/images/profile-picture.png https://cdn.slidesharecdn.com/ss_thumbnails/mysecondpapers2ppaper-190612083546-thumbnail.jpg?width=320&height=320&fit=bounds slideshow/wear-properties-of-thixoformed-al57si2cu03mg-aluminium-alloy/149289571 Wear Properties of Thi... https://cdn.slidesharecdn.com/ss_thumbnails/my1stpapaer-190612083412-thumbnail.jpg?width=320&height=320&fit=bounds slideshow/d-ry-sliding-wear-behaviour-o-f-rheocat-al-57si-2cu-03mg-a-l-l-oy/149289516 Dry Sliding Wear Behav...