�ݺ�ߣ

Furniture Fittings and Accessories Components

Chair Parts
Heavy Duty Swivel

12 gauge steel with a double race 10 1/4 by 10 1/4 flat pitch.
Mounting holes are on 8" centers

Swivel Rocker base

Brown legs with plastic feet. Leg span is 25" and comes in
either a 5 1/4" or 6" overall height.

Steam Bent Oak Rocker Runners

Length measures strait across from tip to tip. Stronger than
cut rockers Sold in pairs only. Unfinished red oak will require
drilling sanding and finishing.

1 5/16" high by 34 1/4" long by 5/8" thick

1 5/16" high by 34 1/4" long by 1 1/8" thick


Cut Oak Rocker Runners


1 3/4" high by 37" long by 1 9/16" thick
Curved Rocking Chair Seat

Oak face and back. It must be shaped and cut to fit your
particular rocker. Send us a sketch of your formed shape
before ordering to make sure it will fit. We can provide this
one curvature only. Our supplier doesn't have any other

zaini@selectvest.com Wisdom Management Services (M) Sdn. Bhd. 1


shape molds. 24" to 25"long following the curve. 3/16" thick,
20" plus wide.

Oak Hip Huggers

6 1/2" high by 5 1/4" deep by 7/8" diameter. 11" long from tip
to tip measuring along the curve. **Please note: All
measurements are approximate. One end is sanded flat to fit
the chair seat. The other end is carved out to fit the back
spindle. Screw holes are pre-drilled. Unfinished, sanded,
ready to install. Ends are pointed. One left hand and one right
hand hip hugger required per chair. Sold in pairs only.

Hip hugger Clips

Outside dimensions - 1" long by 11/16" wide by 1/2" high.
Screw hole - 1/4" diameter. Made to fit 7/8" hiphuggers. Sold
in sets of four.

Morris Chair Brackets

7 3/4" long by 15/16" wide. Hooks will accommodate 3/8" to
1/2" diameter rods. The common angle of the brackets will
adapt to the curve of most Morris chairs. Sold by the pair.

Morris Chair Rod

Overall - 29 3/4" long.

Rod - 28 1/4" long by 3/8" diameter. Beehive finials - 3/4"
long by 7/8" diameter.

Finials are attached with set screws which can be removed,
allowing the rod to be cut to length if necessary.



Platform Rocker Springs

All springs are sold by the pair which will do one chair.

Heavy Duty - 7 gauge Eight turns.

Single Juvenile Platform Rocker Springs.

Oak High Chair Parts

20 1/2" wide 11 3/4" deep. 1 3/32" thick with Routed
center.

16" wide by 8 1/2" deep at center. 7" deep at ends.

16" wide by 8" deep.

Bent Oak High Chair Tray Arms

Overall length - 18 1/2" long 23" long following the curve.
Flat area - Approximately 13" 7/8" Square. Sold by the pair
with spacers.

High Chair Tray Hardware

Arm piece - 6" L x 5/8" w x 7/8" deep. Tray Piece - 3 5/16" L
x 1" w x 15/16" deep.

Best for use with our W3-5226 tray or similar styles only.
Comes as a set for attaching one high chair tray. The long
piece attaches to the outside of the arm. The short piece
attaches to the underside of the tray. The spring loaded clamp
allow the position of the tray to be adjusted then locked into



place.
High Chair Safety Strap
13" long by 5/8" wide Natural leather. Includes screw snap
for easy installation.

Finials, Spindles, Pegs

5 inches tall and 3 inches in diameter Pine

Pine fence post finial 4 1/2" tall and 3"

Turned length - 2 1/4" Overall length - 3 1/8"

Maximum diameter - 15/16" Tenon diameter - 3/8"



Turned length - 3 3/32" Overall length - 3 3/4"

maximum diameter - 1 5/8" Tenon diameter - 3/8"

Turned length - 2" Overall length - 2 7/16"
Maximum diameter - 13/16" Tenon diameter - 1/2"


�ݺ�ߣ

Components

More Related Content

Components