�ݺ�ߣ

MOHAMED ZAKARIA KAMEL.
Address: El Marge El Gadeda, El Khanka, Qalyoubya, Egypt.
Mob 1: + (20) 106 9195 061
Mob 2: + (20) 100 2182 366
E-mail: Moh.zk87@gmail.com
OBJECTIVE:
I am actively seeking for Automation & Control Engineer role utilizing my extensive
work experience in Automation and Control Field This included design, construction
and commissioning.
Work Experience:
 Automation and control Engineer at TRICOM controls (Siemens partner) from
January 2015 till now
 Study the projects and Prepare shop drawing for approval or modification.
 Handle technical studies and review orders to be sure that all client specification is
strictly followed.
 Prepare Final Submittal for projects.
 Design and check the configuration required (using Siemens SIMATIC systems and
softwares: Logo, Step 7 PLCs, HMI, and SCADA).
 Performing FAT and SAT test according to the contract.
 Installation for automation panels.
 Startup and commissioning for automation panels at the site.
 Automation and control Engineer at EMAS-ELSWEDI (Siemens partner) from
December 2011 to January 2015
 Study the projects and prepare Technical and Commercial offers.
 Prepare shop drawing for approval or modification.
 Handle technical studies and review orders in hand
to be sure that all client specification is strictly followed.
 Prepare Final Submittal for projects.
 Design and check the configuration required (Using Siemens SIMATIC systems and
softwares: Logo, Step 7 PLCs, HMI, and SCADA) and (Using Siemens Drives
MICROMASTER 440 SINAMICS G120 Drives).
 Performing FAT and SAT test according to the contract.
 Installation for automation panels.
 Startup and commissioning for automation panels at the site.

Projects:
1. PLC & SCADA Fire fighting system for RAS GHAREB Petroleum Treatment
Station.
Client: Egyptian maintenance company (EMC).
Description: based on Siemens (PLC S7-400 5H, Distributed I/Os ET200M, fail safe
signal modules and WINCC SCADA)
This was a control system utilizing the S7-400 PLC to control Fire fighting System
(Valves, Pressure switches, temper switches, linear heat detectors, gas transmitters
and Smoke/Heat detectors through server pc station and MIMIC’s.
Software used: SIMATIC STEP7 5.5, WINCC 7.0.
2. PLC & SCADA Industrial Gas Monitoring Center.
Client: EZZ DEKHEILA STEEL COMPANT (EZDK)
Description: based on Siemens (PLC S7-300 Stations, WINCC SCADA)
This was a control system utilizing the PLC S7-300 stations to monitoring industrial
gases from the factories. The factories connected to each other with fiber optical
cables and used OLM device to connect fiber network with the PROFIBUS network.
SIMATIC PC working as Server to Monitor Gases.
Software used: SIMATIC STEP7 5.5, WINCC 7.0.
3. Water Potable and Irrigation Pump Station.
Client: ORASCOM - Cairo Festival City CFC.
Description: based on Siemens (PLC S7-300)
This was a control system utilizing the S7-300 PLC control Water Potable and
Irrigation Pump Station.
Software used: SIMATIC STEP7 5.5.
4. Sewage Pump Station.
This was a control system utilizing the S7-300 PLC control Sewage Pump Station.
Software used: SIMATIC STEP7 5.5.
5. Upgrade CORC Water station.
Client: Cairo Oil Refining Company (CORC) .
This was a control system utilizing the S5 PLC replaced with S7-300 PLC and SCADA .
Software used: SIMATIC STEP7 5.5, TIA WINCC ADVANCED V13.
6. SCADA Boiler.
Client: Nasr Petroleum Company, Suez Egypt (NPC)
Software used: WINCC 7.3.
7. EMCS (Electrical Monitoring and Control System)
Client: ABU QIR THERMAL POWER PLANT UNITS 6&7 (West Delta Production
Company WDPCO)
Description: Based on Siemens (S7-400H, S7-300, Distributed I/Os ET200M,
SIMATIC panel mounted touch HMI, WINCC SCADA and SCALANCE networking
system).

This was a monitoring and control system utilizing the S7-400H and S7-300 PLC to and
WINCC SCADA and local panel mounted HMI to operate, monitor, control, present
log, print alarms, events, and trends recorded process variables. The system included
the logic interlocks for manual operation of fast transfer system; the system had a
redundant communication network and redundant PLC architecture by using Fiber
optical, PROFIBUS and MPI Cables where high availability was required, a Server,
Engineering station, and Operator station.
The system was then connected to the DCS of the plant utilizing OPC protocol.
Software used: SIMATIC STEP7 5.5, WINCC flexible 2008, WINCC 7.0.
8. Tunnel Lighting.
Description: based on Siemens (PLC S7-300, MP 377 12'' HMI, LUX Sensors and
Temperature Sensors)
This was a control system utilizing the S7-300 PLC, LUX sensors to control Tunnel
Lighting and Temperature sensors to control Fans of room panel
The HMI display was installed to monitor and present alarms of the system and allow
the operator to adjust Tunnel Lighting and Fans of room panel operation.
Software used: SIMATIC STEP7 5.5, WINCC flexible 2008.
9. El AMRIYA Sewage Plants.
Client: (Alexandria General Organization for Sanitary Drainage AGOSD) in El AMYRIA
Alexandria.
Description: based on Siemens (PLC S7-1200, GSM Communication Processor
Module (CP1242-7) and KTP1000 HMI)
This was a control system utilizing the S7-1200 PLC and GSM Communication
Processor Module (CP1242-7) to control four Sewage plants distance between them
more than 40 Km the control system
The HMI display was installed to monitor and present alarms of the system and allow
the operator to control four Sewage plants.
Software used: TIA Portal STEP 7 Basic V12.0, TELECONTROL SERVER BASIC.
Education:
B.Cs degree in Electrical Engineering from Shoubra, BENHA University, Egypt 2011.
 Department : Electrical Power & Machines
 Graduation Project title: Mixing Tanks with Level Control based on PLC S7-300, HMI
and MICROMASTER 440
 Overall Grade: Good.
 Graduation Project Grade: Excellent.
Courses:
 Automatic Control Course
 PLC Advanced Course
 Electrical Distribution System Course

Skills:
 Language Skills:
 Native language: Arabic.
 Very good at written and spoken English.
 Technical Skills:
 PLC: Siemens Step 7 PLCs S7-300 and S7-400 through SIMATIC STEP7 5.5 Software,
,S7-200 through Micro Win Software, S7-1200 and S7-1500 through TIA Portal
SIMATIC STEP7 Profissinal v13 Software and Siemens LOGO through LOGO soft
comfort Software.
 PLC: Siemens Fail Safe Systems through CFC and Fail Safe softwars
 SCADA Systems through WINCC 7.0 and WINCC 7.3 Software.
 HMI touch panel of Siemens through WINCC flexible 2008 and TIA Portal SIMATIC
WINCC Profissinal v13.
 Motor Management and Control Devices SIMOCODE
 Siemens Drives(MICROMASTER and SINAMICS); Programming and installing Variable
Speed Drives “INVERTER “
 AutoCAD.
 Automatic Control Circuits.
 Computer Skills:
 Prefect Working knowledge of MS Windows, Word and Excel.
 Prefect Working knowledge of Visio
 Good Working knowledge of Photoshop.
 Internet research skills.
 Personal Skills:
 Working under pressure.
 Understanding of teamwork spirit requirements.
 Committed and willing to learn.
 Flexible and Self-motivated.
 Time -oriented.
Summer Training & Workshops:
 Mar.2011 PLC Workshop at (SIEMENS EGYPT)
 Mar.2011 HMI and WINCC flexible Workshop at (SIEMENS EGYPT)
 Jul.2010 Training Center Networks - South Cairo Electrical Power Plant Station.
 Aug.2008 SHOUBRA- El KHIMA Electrical Power Plant Station.
Awards:
 Member of the INDAC (INDUSTRY ACADEMIA ANNUAL COMPETITION)
Cooperation between Siemens S.A.E. and the Industrial Training Council of year
2011.
 INDAC 2011 Award Third Place for Mixing Tanks with Level Control Project.
Personal Information:
Date of Birth: 19th. December, 1987.
Place of Birth: El Qalag.
Marital status: Married.
Nationality: Egyptian.
Religion: Muslim.
Military Situation: Exempted.

�ݺ�ߣ

Mohamed Zakaria 01-2017

Recommended

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Mohamed Zakaria 01-2017 (20)

Mohamed Zakaria 01-2017