More Related Content
What's hot (18)
Viewers also liked (20)
Similar to Ahmed10 (20)
Ahmed10
- 1. Page 1 of 6 (Ahmed El Sawy) CV. Updated on 15.07.2016 Ahmed Mahmoud El Sawy Mechanical Engineer CSWIP Welding Inspector (Level II) ¨C API 570 Piping Inspector Personal Information: Date of Birth 01 November 1986. Marital Status Single. Contacts: engineary@yahoo.com a.elsawy@alayuni.com +20-1225333500 +966-593094488 Educational Qualification: Degree Speciality Institute/University Bachelor's degree of Mechanical Power Engineering Specialized in construction and welding inspection of steel tanks, piping and pipelines. Alexandria University June-2010. Languages: Arabic: (Native) Reading Writing Speaking English: (V.Good) Reading Writing Speaking Other(s): N/A N/A N/A Executive Summary: Total Years of Experience More than 5 Years Designation Mechanical Engineer (Piping & Welding) ? Design, fabrication and construction of steel tanks for oil storage. ? Preparation and erection of mechanical skids in the power plants. ? Erection of all piping systems in gas turbine including lube oil system, hydraulic oil system, fuel oil system, cooling water system, draining system, ignition gas system, N2 system, blow off system, pressure measuring piping system¡ etc. ? Fabrication, erection, welding, testing and flushing of piping systems in and balance of plant (BOP) including black start diesel generator, DFO system, crude oil system, compressor air system, service air system, CO2 system and fire fighting system. ? Review all engineering / fabrication drawings (P&ID, layout and isometric). ? Applying all NDE (VT, PT, interpretation of RT films) according to ASME Code. ? Perform material receiving inspection according to EN 10204 (3.1). ? Monitor WQT in line with client reference specification. ? Surveillance of all fit-up and welding activities and make visual inspection for welded joints before, during and after welding. ? Preparation of WPS, PQR, WPQ, ITP, method statement, welding book, all NDE procedures and all other QC documentations and reports. ? Perform daily and comprehensive reports to line supervisor. ? Provision of Quality Assurance input to Inspection & Test Plans / Quality Plans.
- 2. Page 2 of 6 (Ahmed El Sawy) CV. Updated on 15.07.2016 Professional Experience: EXECUTIVE PROJECT EXPERIENCE Company: SADELMI Power s.r.l. Project name: QAPCO Project ¨C State of Qatar. Position : Mechanical Commissioning Engineer Period : Start: May/2016 End: To Present Client : Qatar Petrochemical Company. Project Budget: 69 Million Euro Project description : Engineering, Design, Supply, Installation, Commissioning & Testing of Gas Turbines (Replacement of GT1 & GT2, Refurbishment of GT3, GT4 & GT5 and installation of new GT6) on Turn-key basis. Employee¡¯s role & responsibility in the project: Responsible for pre-commissioning and commissioning for all mechanical activities in GT and BOP area, in-line with different vendors. Technologies and methodologies used by the employee in the project: xxxxx. Company: SADELMI Power / Al Ayuni Contracting and Investment Company. Project name: ARAR POWER PLANT EXT. IV ¨C Saudi Arabia. Position : Mechanical Engineer ¨C Welding Inspector Period : Start: June 2014 End: May 2016 Client : Saudi Electricity Company ¨C Kingdom of Saudi Arabia. Project Budget: 309 Million SAR Project description : Design, construct, erect, test, commission, and put into service two new Power Plant Units (55-70 MW each Unit). Employee¡¯s role & responsibility in the project: Responsible for erection, welding and testing of all tanks and piping systems, plus mechanical installation in GT and BOP area.
- 3. Page 3 of 6 (Ahmed El Sawy) CV. Updated on 15.07.2016 Company: Arab Contracting Company (ARCONS) ¨C Egypt. Project name: Zero Liquid Discharge - Misr Fertilizers Co.(MOPCO) - Egypt. Position : QA/QC Engineer Period : Start: December 2013 End: May 2014 Client : Veolia Water Solution Egypt (VWSE). Project Budget: N/A. Project description : Design, Fabrication, Erection, Welding, Painting and Testing of two carbon steel tanks in ZLD. Employee¡¯s role & responsibility in the project: Responsible for steel fabrication and mechanical construction and testing of Tanks. Company: Arab Contracting Company (ARCONS) ¨C Egypt. Project name: Egyptian Indian Polyester Company (EIPET)- Egypt. Position : Construction Engineer Period : Start: July 2012 End: December 2013 Client : Oerlikon BARMAG / EIPET. Project description : Erection of four Tanks with 6200 cubic meter capacity per tank & made of special material cladded carbon steel (double layer CS/SS), also our scope include the Installation of Tankage Piping Network 2000 inch of welded joints. Employee¡¯s role & responsibility in the project: Responsible for steel fabrication, mechanical construction and testing of Tanks.
- 4. Page 4 of 6 (Ahmed El Sawy) CV. Updated on 15.07.2016 Company: Water Dynamics ¨C Egypt. Project name: Marina sewage water treatment station - Egypt. Position : Mechanical Engineer Period : Start: February 2011 End: June 2012 Client : METITO Company. Project description : Installation of treatment station for sewage water. Employee¡¯s role & responsibility in the project: Responsible for installation activities of mechanical equipment and piping. Membership: 1. Saudi Council of Engineers For Life Member Since June/2014 2. Egyptian For Life Member Since September/2010 Training & Certificates: No. Training name Organization Expiration Date Exams or certificates 1 CSWIP ¨C Level II TWI Ltd. June 2017 CSWIP Welding Inspector Certificate # 66420. 2 API 570 API April 2019 API 570 Piping Inspector Certificate # 64720 3 ASNT-NDT - II STE December 2018 VT ¨C PT ¨C MT - RT
- 5. Page 5 of 6 (Ahmed El Sawy) CV. Updated on 15.07.2016
- 6. Page 6 of 6 (Ahmed El Sawy) CV. Updated on 15.07.2016