狠狠撸

Part number 48144004
1st
edition English
May 2017
SERVICE MANUAL
3152
3162
Draper Header
PIN YHH051300 and above
Printed?in U.S.A.
? 2017 CNH Industrial America LLC. All Rights Reserved.
Case IH is a trademark registered in the United States and many
other countries, owned by or licensed to CNH Industrial N.V.,
its subsidiaries or affiliates.

SERVICE MANUAL
3152 Rigid draper header (40 ft), export [YHH051300 - ], 3152 Rigid draper
header (45 ft) [YHH051300 - ], 3152 Rigid draper header (45 ft), export
[YHH051300 - ], 3152 Rigid draper header (25 ft) [YHH051300 - ], 3152
Rigid draper header (30 ft) [YHH051300 - ], 3152 Rigid draper header (35
ft) [YHH051300 - ], 3152 Rigid draper header (40 ft) [YHH051300 - ], 3152
[YHH051300 - ], 3162 Flex draper header (25 ft) [YHH051300 - ], 3162
Flex draper header (30 ft) [YHH051300 - ], 3162 Flex draper header (35 ft)
[YHH051300 - ], 3162 Flex draper header (40 ft) [YHH051300 - ], 3162 Flex
draper header (40 ft), export [YHH051300 - ], 3162 Flex draper header (45
ft) [YHH051300 - ], 3162 Flex draper header (45 ft), export [YHH051300 - ],
3162 [YHH051300 - ]
48144004 08/05/2017
EN

Contents
INTRODUCTION
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.300] Reservoir, cooler, and filters........................................................ 35.2
[35.359] Main control valve.................................................................. 35.3
[35.420] Reel vertical positioning system.................................................... 35.4
[35.430] Reel fore-and-aft positioning system............................................... 35.5
[35.910] Head and header hydraulic drive .................................................. 35.6
Wheels...................................................................................... 44
[44.536] Gauge wheels...................................................................... 44.1
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.670] Header leveling control............................................................. 55.3
[55.675] Reel speed and position control.................................................... 55.4
[55.421] Feeding control system ............................................................ 55.5
[55.404] External lighting .................................................................... 55.6
Attachments/Headers.................................................................. 58
[58.100] Attachment/Header support and drives ............................................ 58.1
[58.101] Attachment/Header reel............................................................ 58.2
[58.105] Attachment/Header reel control system............................................ 58.3
[58.110] Attachment/Header cutting mechanism ............................................ 58.4
[58.120] Attachment/Header feed auger .................................................... 58.5
[58.130] Attachment/Header frame.......................................................... 58.6
[58.224] Header drive ....................................................................... 58.7
[58.900] Belt feeding ........................................................................ 58.8
48144004 08/05/2017

Platform, cab, bodywork, and decals............................................. 90
[90.105] Machine shields and guards ....................................................... 90.1
48144004 08/05/2017

INTRODUCTION
48144004 08/05/2017
1

Contents
INTRODUCTION
Foreword - Important notice regarding equipment servicing (*) ................................ 3
Safety rules - Ecology and the environment (*) ................................................. 4
Safety rules (*) .................................................................................. 5
Safety rules - Personal safety (*) ............................................................... 6
Power Take-Off (PTO) shaft - Safety rules - Power Take-Off (PTO) (*) ......................... 7
Transport locking assembly Cylinder stop - Safety rules - Lift cylinder safety locks (*) ......... 8
Safety signs (*) ................................................................................ 10
Torque - Minimum tightening torques for normal assembly (*) ............................... 21
Torque - Standard torque data for hydraulics (*) .............................................. 26
Basic instructions - Shop and assembly (*) ................................................... 28
Basic instructions - Chain wear tables - Roller chains (*) ..................................... 30
General specification - General welding (*) ................................................... 32
General specification Machine specifications - Flex headers (*) ............................. 33
General specification Machine specifications - Rigid headers (*) ............................ 35
Capacities (*) ................................................................................. 37
Product identification (*) ...................................................................... 39
Machine orientation - Machine orientation .................................................... 40
(*) See content for specific models
48144004 08/05/2017
2

INTRODUCTION
Foreword - Important notice regarding equipment servicing
3152
3162
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
48144004 08/05/2017
3

INTRODUCTION
Safety rules - Ecology and the environment
3152
3162
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
? Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
? In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
? Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
? Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
? Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
? The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
? Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
? Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
? Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. CASE IH
strongly recommends that you return all used batteries to a CASE IH dealer, who will
dispose of the used batteries or recycle the used batteries properly. In some countries,
this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
? Accept the return of your used batteries
? Store the returned batteries in a suitable location
? Send the returned batteries to the battery manufacturer for recycling
48144004 08/05/2017
4

INTRODUCTION
Safety rules
3152
3162
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
48144004 08/05/2017
5

INTRODUCTION
Safety rules - Personal safety
3152
3162
Carefully study these precautions, and those included in the external attachment operators
manual, and insist that they be followed by those working with and for you.
1. Thoroughly read and understand this manual and the attachment Operator’s Manual before operating this or any
other equipment.
2. Be sure all people and pets are clear of the machine before starting. Sound the horn, if equipped, three times
before starting engine.
3. Only the operator should be on the machine when in operation. Never allow anyone to climb on to the machine
while it is in motion. If the machine is equipped with an Instructors Seat, this must only be used for training
purposes. Passengers must not be allowed to use the Instructors Seat.
4. Keep all shields in place. Never work around the machine or any of the attachments while wearing loose clothing
that might catch on moving parts.
5. Observe the following precautions whenever lubricating the machine or making adjustments.
? Disengage all clutching levers or switches.
? Lower the attachment, if equipped, to the ground or raise the attachment completely and engage the cylinder
safety locks. Completing these actions will prevent the attachment from lowering unexpectedly.
? Engage the parking brake.
? Shut off the engine and remove the key.
? Wait for all machine movement to stop before leaving the operators platform.
6. Always keep the machine in gear while travelling downhill.
7. The machine should always be equipped with sufficient front or rear axle weight for safe operation.
8. Under some field conditions, more weight may be required at the front or rear axle for adequate stability. This is
especially important when operating in hilly conditions or/when using heavy attachments.
9. Always lower the attachment, shut off the engine, set the parking brake, engage the transmission gears, remove
the key and wait for all machine movement to stop before leaving the operators platform.
10. If the attachment or machine should become obstructed or plugged; set the parking brake, shut off the engine
and remove the key, engage the transmission gears, wait for all machine or attachment motion to come to a stop,
before leaving the operators platform to removing the obstruction or plug.
11. Never disconnect or make any adjustments to the hydraulic system unless the machine and/or the attachment is
lowered to the ground or the safety lock(s) is in the engaged position.
12. Use of the flashing lights is highly recommended when operating on a public road.
13. When transporting on a road or highway, use accessory lights and devices for adequate warning to the opera-
tors of other vehicles. In this regard, check local government regulations. Various safety lights and devices are
available from your CASE IH dealer.
14. Practice safety 365 days a year.
15. Keep all your equipment in safe operating condition.
16. Keep all guards and safety devices in place.
17. Always set the parking brake, shut off the engine and remove the key, engage the transmission gears, wait for all
machine or attachment motion to come to a stop, before leaving the operators platform to service the machine
and attachment.
18. Remember: A careful operator is the best insurance against an accident.
19. Extreme care should be taken in keeping hands and clothing away from moving parts.
48144004 08/05/2017
6

INTRODUCTION
Power Take-Off (PTO) shaft - Safety rules - Power Take-Off (PTO)
3152
3162
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
The Power Take-Off (PTO) shaft on your header is
equipped with a drive shaft shield (1) and chains. The
shields protect the operator from the PTO shaft while the
shaft is rotating. The shield chains prevent the shield
from rotating while the PTO shaft is connected to the
combine and turning.
83112562 1
The rear PTO shaft, that connects to the combine, right-
hand side chain (1) is attached to a loop in the adapter.
Connect the left hand shield chain to the hole provided in
the steel PTO slip clutch shield.
83118612 2
The front PTO shaft, that drives the auger, right-hand side
chain (1) hooks to hole in backsheet (2).
Left side chain (4) hooks to hole in backsheet (3).
83112562A 3
48144004 08/05/2017
7

INTRODUCTION
Transport locking assembly Cylinder stop - Safety rules - Lift
cylinder safety locks
3152
3162
WARNING
Crushing hazard!
ALWAYS make sure the work area is clear of bystanders and domestic animals before raising or low-
ering the equipment.
Failure to comply could result in death or serious injury.
W0123A
Your CASE IH header is equipped with reel lift cylinder
locks (1).
NOTE: The header must be connected to the combine for
operation.
To engage the lift cylinder locks:
1. Use your combine’s reel lift switch to raise the reel
completely.
2. Lift the lock from its storage holder (2).
83112567 1
Left-hand side
83112568 2
Right-hand side
48144004 08/05/2017
8

INTRODUCTION
3. Swing the lock (1) down over the cylinder shaft.
83114725 1 3
Left-hand side
83117559 4
Center, split reel equipped only
83112595 5
Right-hand side
To store the locks:
1. If the reel has settled so that the locks are against
the cylinders;
? Raise the reel to it's highest point.
2. Raise the lock from the cylinder and place it in on the
storage hanger (1).
3. Lower the reel to the desired height.
83114726 6
48144004 08/05/2017
9

INTRODUCTION
Safety signs
3152 Rigid draper header (40 ft), export [YHH051300 - ]
3152 Rigid draper header (45 ft) [YHH051300 - ]
3152 Rigid draper header (45 ft), export [YHH051300 - ]
3152 [YHH051300 - ] ANZ --- APAC --- MEA --- NA --- WE ---
3162 Flex draper header (25 ft) [YHH051300 - ]
3162 Flex draper header (40 ft), export [YHH051300 - ]
3162 Flex draper header (45 ft), export [YHH051300 - ]
3162 [YHH051300 - ] ANZ --- APAC --- MEA --- WE ---
The following safety signs are placed on your machine as a guide for your safety and for those working with you. Walk
around the machine and note the content and location of these safety signs before operating your machine.
Keep safety signs clean and legible. Clean safety signs with a soft cloth, water, and a gentle detergent. Do not use
solvent, gasoline, or other harsh chemicals. Solvents, gasoline, and other harsh chemicals may damage or remove
safety signs.
Replace all safety signs that are damaged, missing, painted over, or illegible. If a safety sign is on a part that is
replaced, make sure the safety sign is installed on the new part. See your dealer for replacement safety signs.
Safety signs that display the “Read Operator’s Manual” symbol are intended to direct
the operator to the operator’s manual for further information regarding maintenance,
adjustments, or procedures for particular areas of the machine. When a safety sign
displays this symbol, refer to the appropriate page of the operator’s manual.
83112557 1
Rear view
48144004 08/05/2017
10

INTRODUCTION
NHIL16GH00436AA 2 NHIL16GH00437AA 3
Left - hand side Right - hand side
WARNING
Slippery surface.
Do not use this area as a step or platform.
Failure to comply could result in death or serious
injury.
Quantity: 2
87026533
87026533_B 4
(4) Left-Hand (LH) side of feeder opening on the top rail.
93112558 5
(7) Right-Hand (RH) side of feeder opening on the top
rail.
93112558 6
48144004 08/05/2017
11

INTRODUCTION
WARNING
Crush Hazard.
Engage safety latch before working under machine.
Failure to comply could cause death or serious
injury.
Quantity: 2
84027712
87027712 7
(9) RH side feeder opening.
83112566 8
(11) LH side feeder opening.
83112563 9
48144004 08/05/2017
12

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

INTRODUCTION
WARNING
Shield is missing.
Stand clear.
Replace or close shield before operating machine.
Failure to comply could cause death or serious
injury.
Quantity: 1
86999254
86999254 10
(15) LH side feeder opening.
83112561 11
48144004 08/05/2017
13

INTRODUCTION
DANGER
Rotating drive line.
Keep all shields and guards in place.
Failure to comply will result in death or serious
injury.
Quantity: 2
86520062
86520062_B 12
(2) On the Power Take-Off (PTO) PTO shaft cover.
83112562 13
(12) On the PTO shaft cover.
83112562 14
48144004 08/05/2017
14

INTRODUCTION
CAUTION
Stay clear of hot surface.
Failure to do so could result in minor or moderate
injury.
Quantity: 2
84004742
84004742 15
(3) On the hydraulic reservoir.
NHIL12GH00272AA 16
(8) On the hydraulic reservoir.
NHIL12GH00273AA 17
48144004 08/05/2017
15

狠狠撸

Case ih 3162 flex draper header (40 ft), export service repair manual [yhh051300 ]

Recommended

More Related Content

More from ujfjjsjkkemee (13)

Recently uploaded (20)

Case ih 3162 flex draper header (40 ft), export service repair manual [yhh051300 ]