際際滷

際際滷Share a Scribd company logo

Dimensioning standards

Download as PPT, PDF
S
Suresh Kothandaraman

This document discusses dimensioning standards and practices. It provides information on: - Following standards from organizations like ANSI, ISO, and DIN to ensure drawings are dimensioned consistently. - The components of linear dimensions like dimension text, lines, and arrowheads. - Methods for dimensioning different features like circles, arcs, angles, holes, and threads. - Techniques like datum dimensioning to minimize tolerance accumulation versus chain dimensioning. - Reading dimensioning symbols and thread and hole notes.

1 of 52
Downloaded 124 times
Forging new generations of engineers
Dimensioning Standards
Rules and Practices Accurate dimensioning is one of the most demanding undertakings when designing parts. Use the checklist to insure you have followed the basic dimensioning rules. Keep in mind there may be a case where the need to break a standard could occur to give clarity to the part and manufacturer.
Standards In order for the drawings to be dimensioned so that all people can understand them, we need to follow standards that every company in the world must follow. Standards are created by these organizations: -ANSI -MIL -ISO -DOD -DIN -CEN -JIS
Standards Institutions ANSI - American National Standards Institute - This institute creates the engineering standards for North America. ISO - International Organization for Standardization - This is a world wide organization that creates engineering standards with approximately 100 participating countries.
Standards Institutions DIN - Deutsches Institut f端r Normung - The German Standards Institute created many standards used world wide such as the standards for camera film. JIS - Japanese Industrial Standard - Created after WWII for Japanese standards. CEN - European Standards Organization
Standards Institutions The United States military has two organizations that develop standards. DOD - Department Of Defense MIL - Military Standard
Linear dimensions are comprised of four components: Dimension Text Dimension Lines Arrow Heads Extension Lines
Extension Lines Continue 1/8 past the dimension line Extended from the view to indicate the edges referenced and hold the dimension line 1/16 gap from the view so they are not confused with the visible lines
Dimension Lines Horizontal Aligned to a slanted surfaced Vertical When stacked, they are 10mm (.4) from the view and 6mm(.25) apart.
Arrowheads (Dimension Line Terminator) Arrowheads are typical dimension line terminators. There are other acceptable dimension line terminators. Arrowheads point directly to the object that is being dimensioned or the extension lines at the end of the dimension. Arrowheads are made three times as long as they are wide. Dot Oblique or architectural ticks used in architectural drawings Datum
Dimension Text If the dimension text will not fit between the extension lines, it may be placed outside them. Dimension text is placed in the middle of the line both horizontally and vertically.
Dimensioning Methods Dimensions are represented on a drawing using one of two systems, unidirectional or aligned. The unidirectional method means all dimensions are read in the same direction. The aligned method means the dimensions are read in alignment with the dimension lines or side of the part, some read horizontally and others read vertically.
Dimension Text Unidirectional vs. Aligned Unidirectional dimensions are placed so they can be read from the bottom of the drawing sheet. This method is commonly used in mechanical drafting. Aligned dimensions are placed so the horizontal dimensions can be read from the bottom of the drawing sheet and the vertical dimensions can be read from the right side of the drawing sheet. This method is commonly used in architectural and structural drafting.
Types of Dimensions There are two classifications of dimensions: size and location. Size dimensions are placed in direct relationship to a feature to identify the specific size. Location dimensions are used to identify the relationship of a feature to another feature within an object.
Dimensioning Checklist Each dimension should be written clearly with only one way to be interpreted. A feature should be dimensioned only once. Dimension and extension lines should not cross. Each feature should be dimensioned. Dimension features or surfaces should be done to a logical reference point.
Dimension Checklist Dimension circles should have diameters and arcs with a radius. A center line should be extended and used as an extension line. Dimension features on a view should clearly show its true shape. Enough space should be provided to avoid crowding and misinterpretation.
Dimension Checklist Extension lines and object lines should not overlap. Dimensions should be placed outside the part. Center lines or marks should be used on all circles and holes.
Linear Dimensioning Dimensioning from feature to feature is known as Chain Dimensioning.. It is commonly used and easy to lay out. It does have possible consequences in the manufacturing of a part. Tolerances can accumulate, making the end product larger or smaller than expected.
Chain Dimensioning This is a general note. It indicates that all two place decimal dimensions have a tolerance of plus or minus .01 inch unless otherwise specified.
Chain Dimensioning Each of these steps can range between . 490 and .510 wide.
Chain Dimensioning The chain dimensioning layout can have an effect on the final length of the part ranging from 1.47 to 1.53.
Chain Dimensioning Placing an overall dimension will limit the chain effect of the tolerance build up.
Linear Dimensioning The accuracy of the final product is determined by the dimensions on the drawing. If all the dimensions originate from a common corner of the part, the object will be more accurate. This is referred to as Datum Dimensioning. Datums insure the tolerance or errors in manufacturing do not accumulate.
Datum Dimensioning The dimensions originate from a common edge (DATUM) of the part.
Datum Dimensioning The dimensions originate from a common edge (DATUM) of the part. This is a general note. It indicates that all two place decimal dimensions have a tolerance of plus or minus . 01 inch unless otherwise specified.
Datum Dimensioning This step can be .490 to .510 wide. This distance can be 1.49 to 1.510 wide. This distance can be .990 to 1.010 wide.
Dimensioning Symbols
Dimensioning Angles Angled surface may be dimensioned using coordinate method to specify the two location distances of the angle. Angled surfaces may also be dimensioned using the angular method by specifying one location distance and the angle.
Dimensioning Angles Coordinate Method Angular Method
Dimensioning Arcs and Circles Arcs and circles are dimensioned in views that show the arc or circle. Arcs are dimensioned with a leader to identify the radius; in some cases, a center mark is included. Circles should have a center mark and are dimensioned with a leader to identify the diameter.
Dimensioning Curved Features and Arcs The arrow can be inside for small arcs. Use a capital R for dimensioning arcs. Small arcs do not need center marks. Arrow can be outside. Large Arcs use center marks.
Diameters A full circular object should be dimensioned using its diameter. Holes should use hole notes. This specification calls for a hole with a .5 diameter and 1.00 deep.
Diameters Cylindrical parts may show their diameters in this manner. Dimensioning on the right side view could be too crowded. Note that the diameter symbol is used so it is not confused with a linear dimension.
Chords Chords may be dimensioned in one of the following ways.
Dimensioning Curved Features Points are placed along the contour and are dimensioned from the datum. Datum
Reference Dimensions Designates more than one of the same feature. In this case, it is identifying there are two identical holes.
Chamfers External chamfer for 45 degree chamfers only. There are two options. Internal chamfers. External chamfer for angles other than 45 degrees.
Fillets and Rounds Fillets Rounds
Fillets and Rounds Large arcs use center marks. Use a capital R for dimensioning the arc. Small arcs do not need center marks. Arrow can be outside the arc.
Conical Tapers
Slot Dimensioning The two methods shown on the left are the acceptable methods for dimensioning slotted holes.
Dimensioning Radial Patterns Angles and radius values are used to locate the centers of radial patterned features, such as the holes on this plate.
Keyway and Keyseat Keyway Keyseat
Keyways Keyway Dimensions Shaft
Hole Dimensioning Holes are specified with numbers and symbols.
Reading a Hole Note The Hole Diameter is .25 and will be drilled .75 deep. The Hole will be Counterbored to a .38diameter and to a depth of .25 Counterbore or Spotface Symbol Depth Symbol
Reading a Hole Note The Hole Diameter will be .38 drilled .5 deep.
Reading a Hole Note The Hole Diameter will be .38 through the whole block.
Reading Thread Notes Threads are dimensioned with the use of local notes. We will discuss two methods: the ISO and the Unified National Thread method.
Reading a Unified National Thread Note Threads per Inch Major Diameter Identifies coarse or fine thread. In this case, C for coarse. F is for fine.
Reading a ISO Thread Notes This number can be 3,4,5,6,7,8,9. It is the grade of tolerance in the threads from fine to coarse. The H is for allowance: G would be a tight allowance and H is no allowance. Pitch of the threads. Nominal Diameter In Millimeters M for Metric Prior to THRU, you may have an LH for left hand thread. Finally THRU or a depth may be specified.

More Related Content

Dimensioning standards

  • 1. Forging new generations of engineers
  • 3. Rules and Practices Accurate dimensioning is one of the most demanding undertakings when designing parts. Use the checklist to insure you have followed the basic dimensioning rules. Keep in mind there may be a case where the need to break a standard could occur to give clarity to the part and manufacturer.
  • 4. Standards In order for the drawings to be dimensioned so that all people can understand them, we need to follow standards that every company in the world must follow. Standards are created by these organizations: -ANSI -MIL -ISO -DOD -DIN -CEN -JIS
  • 5. Standards Institutions ANSI - American National Standards Institute - This institute creates the engineering standards for North America. ISO - International Organization for Standardization - This is a world wide organization that creates engineering standards with approximately 100 participating countries.
  • 6. Standards Institutions DIN - Deutsches Institut f端r Normung - The German Standards Institute created many standards used world wide such as the standards for camera film. JIS - Japanese Industrial Standard - Created after WWII for Japanese standards. CEN - European Standards Organization
  • 7. Standards Institutions The United States military has two organizations that develop standards. DOD - Department Of Defense MIL - Military Standard
  • 8. Linear dimensions are comprised of four components: Dimension Text Dimension Lines Arrow Heads Extension Lines
  • 9. Extension Lines Continue 1/8 past the dimension line Extended from the view to indicate the edges referenced and hold the dimension line 1/16 gap from the view so they are not confused with the visible lines
  • 10. Dimension Lines Horizontal Aligned to a slanted surfaced Vertical When stacked, they are 10mm (.4) from the view and 6mm(.25) apart.
  • 11. Arrowheads (Dimension Line Terminator) Arrowheads are typical dimension line terminators. There are other acceptable dimension line terminators. Arrowheads point directly to the object that is being dimensioned or the extension lines at the end of the dimension. Arrowheads are made three times as long as they are wide. Dot Oblique or architectural ticks used in architectural drawings Datum
  • 12. Dimension Text If the dimension text will not fit between the extension lines, it may be placed outside them. Dimension text is placed in the middle of the line both horizontally and vertically.
  • 13. Dimensioning Methods Dimensions are represented on a drawing using one of two systems, unidirectional or aligned. The unidirectional method means all dimensions are read in the same direction. The aligned method means the dimensions are read in alignment with the dimension lines or side of the part, some read horizontally and others read vertically.
  • 14. Dimension Text Unidirectional vs. Aligned Unidirectional dimensions are placed so they can be read from the bottom of the drawing sheet. This method is commonly used in mechanical drafting. Aligned dimensions are placed so the horizontal dimensions can be read from the bottom of the drawing sheet and the vertical dimensions can be read from the right side of the drawing sheet. This method is commonly used in architectural and structural drafting.
  • 15. Types of Dimensions There are two classifications of dimensions: size and location. Size dimensions are placed in direct relationship to a feature to identify the specific size. Location dimensions are used to identify the relationship of a feature to another feature within an object.
  • 16. Dimensioning Checklist Each dimension should be written clearly with only one way to be interpreted. A feature should be dimensioned only once. Dimension and extension lines should not cross. Each feature should be dimensioned. Dimension features or surfaces should be done to a logical reference point.
  • 17. Dimension Checklist Dimension circles should have diameters and arcs with a radius. A center line should be extended and used as an extension line. Dimension features on a view should clearly show its true shape. Enough space should be provided to avoid crowding and misinterpretation.
  • 18. Dimension Checklist Extension lines and object lines should not overlap. Dimensions should be placed outside the part. Center lines or marks should be used on all circles and holes.
  • 19. Linear Dimensioning Dimensioning from feature to feature is known as Chain Dimensioning.. It is commonly used and easy to lay out. It does have possible consequences in the manufacturing of a part. Tolerances can accumulate, making the end product larger or smaller than expected.
  • 20. Chain Dimensioning This is a general note. It indicates that all two place decimal dimensions have a tolerance of plus or minus .01 inch unless otherwise specified.
  • 21. Chain Dimensioning Each of these steps can range between . 490 and .510 wide.
  • 22. Chain Dimensioning The chain dimensioning layout can have an effect on the final length of the part ranging from 1.47 to 1.53.
  • 23. Chain Dimensioning Placing an overall dimension will limit the chain effect of the tolerance build up.
  • 24. Linear Dimensioning The accuracy of the final product is determined by the dimensions on the drawing. If all the dimensions originate from a common corner of the part, the object will be more accurate. This is referred to as Datum Dimensioning. Datums insure the tolerance or errors in manufacturing do not accumulate.
  • 25. Datum Dimensioning The dimensions originate from a common edge (DATUM) of the part.
  • 26. Datum Dimensioning The dimensions originate from a common edge (DATUM) of the part. This is a general note. It indicates that all two place decimal dimensions have a tolerance of plus or minus . 01 inch unless otherwise specified.
  • 27. Datum Dimensioning This step can be .490 to .510 wide. This distance can be 1.49 to 1.510 wide. This distance can be .990 to 1.010 wide.
  • 29. Dimensioning Angles Angled surface may be dimensioned using coordinate method to specify the two location distances of the angle. Angled surfaces may also be dimensioned using the angular method by specifying one location distance and the angle.
  • 31. Dimensioning Arcs and Circles Arcs and circles are dimensioned in views that show the arc or circle. Arcs are dimensioned with a leader to identify the radius; in some cases, a center mark is included. Circles should have a center mark and are dimensioned with a leader to identify the diameter.
  • 32. Dimensioning Curved Features and Arcs The arrow can be inside for small arcs. Use a capital R for dimensioning arcs. Small arcs do not need center marks. Arrow can be outside. Large Arcs use center marks.
  • 33. Diameters A full circular object should be dimensioned using its diameter. Holes should use hole notes. This specification calls for a hole with a .5 diameter and 1.00 deep.
  • 34. Diameters Cylindrical parts may show their diameters in this manner. Dimensioning on the right side view could be too crowded. Note that the diameter symbol is used so it is not confused with a linear dimension.
  • 35. Chords Chords may be dimensioned in one of the following ways.
  • 36. Dimensioning Curved Features Points are placed along the contour and are dimensioned from the datum. Datum
  • 37. Reference Dimensions Designates more than one of the same feature. In this case, it is identifying there are two identical holes.
  • 38. Chamfers External chamfer for 45 degree chamfers only. There are two options. Internal chamfers. External chamfer for angles other than 45 degrees.
  • 40. Fillets and Rounds Large arcs use center marks. Use a capital R for dimensioning the arc. Small arcs do not need center marks. Arrow can be outside the arc.
  • 42. Slot Dimensioning The two methods shown on the left are the acceptable methods for dimensioning slotted holes.
  • 43. Dimensioning Radial Patterns Angles and radius values are used to locate the centers of radial patterned features, such as the holes on this plate.
  • 46. Hole Dimensioning Holes are specified with numbers and symbols.
  • 47. Reading a Hole Note The Hole Diameter is .25 and will be drilled .75 deep. The Hole will be Counterbored to a .38diameter and to a depth of .25 Counterbore or Spotface Symbol Depth Symbol
  • 48. Reading a Hole Note The Hole Diameter will be .38 drilled .5 deep.
  • 49. Reading a Hole Note The Hole Diameter will be .38 through the whole block.
  • 50. Reading Thread Notes Threads are dimensioned with the use of local notes. We will discuss two methods: the ISO and the Unified National Thread method.
  • 51. Reading a Unified National Thread Note Threads per Inch Major Diameter Identifies coarse or fine thread. In this case, C for coarse. F is for fine.
  • 52. Reading a ISO Thread Notes This number can be 3,4,5,6,7,8,9. It is the grade of tolerance in the threads from fine to coarse. The H is for allowance: G would be a tight allowance and H is no allowance. Pitch of the threads. Nominal Diameter In Millimeters M for Metric Prior to THRU, you may have an LH for left hand thread. Finally THRU or a depth may be specified.

Editor's Notes

  • #16: The teacher can give an example on the board or from a part they have created.
  • #24: This overall dimension along with the omission of the last partial dimension also gives the builder a reference edge. (the left edge) This indicates where the steps are to be measured from. Chain dimensioning can lead to a large tolerance build up. This may lead to a part being built that will not function properly. The tolerance of a part must be evaluated by the designer. If a dimensioned does not need to be tightly controlled for the function of the part then it should not be specified. Holding a part to a tight tolerance is much more costly.
  • #28: Datum dimensioning helps keep the tolerances much tighter. Each of the steps has the same plus of minus tolerance of .01. This stops the build up effect that we saw in the chain method.