More Related Content
Similar to Solid_State_Lightning_and_Light emitting diode LEDs.pptx (20)
Recently uploaded (20)
Solid_State_Lightning_and_Light emitting diode LEDs.pptx
- 1. Solid State Lightning and LEDs Dragica Vasileska, ECEE, ASU Fernando Ponce, Physics, ASU
- 11. Solid State Lighting is the most disruptive technology to hit the lighting industry in 50 years
- 14. LIGHT EMITTING DIODES Solid State Lightning
- 15. A light emitting diode (LED) is essentially a PN junction opto-semiconductor that emits a monochromatic (single color) light when operated in a forward biased direction. LEDs convert electrical energy into light energy. They are frequently used as "pilot" lights in electronic appliances to indicate whether the circuit is closed or not.
- 16. About LEDs (1/2) The most important part of a light emitting diode (LED) is the semi-conductor chip located in the center of the bulb as shown at the right. The chip has two regions separated by a junction. The p region is dominated by positive electric charges, and the n region is dominated by negative electric charges. The junction acts as a barrier to the flow of electrons between the p and the n regions. Only when sufficient voltage is applied to the semi-conductor chip, can the current flow, and the electrons cross the junction into the p region.
- 17. How Does A LED Work? (1/2) When sufficient voltage is applied to the chip across the leads of the LED, electrons can move easily in only one direction across the junction between the p and n regions. In the p region there are many more positive than negative charges. When a voltage is applied and the current starts to flow, electrons in the n region have sufficient energy to move across the junction into the p region.
- 18. How Does A LED Work? (2/2) Each time an electron recombines with a positive charge, electric potential energy is converted into electromagnetic energy. For each recombination of a negative and a positive charge, a quantum of electromagnetic energy is emitted in the form of a photon of light with a frequency characteristic of the semi-conductor material (usually a combination of the chemical elements gallium, arsenic and phosphorus)..
- 19. Testing LEDs Never connect an LED directly to a battery or power supply! It will be destroyed almost instantly because too much current will pass through and burn it out. LEDs must have a resistor in series to limit the current to a safe value, for quick testing purposes a 1k resistor is suitable for most LEDs if your supply voltage is 12V or less. Remember to connect the LED the correct way round!
- 20. How Much Energy Does an LED Emit? The energy (E) of the light emitted by an LED is related to the electric charge (q) of an electron and the voltage (V) required to light the LED by the expression: E = qV Joules. This expression simply says that the voltage is proportional to the electric energy, and is a general statement which applies to any circuit, as well as to LED's. The constant q is the electric charge of a single electron, -1.6 x 10-19 Coulomb.
- 21. Finding the Energy from the Voltage Suppose you measured the voltage across the leads of an LED, and you wished to find the corresponding energy required to light the LED. Let us say that you have a red LED, and the voltage measured between the leads of is 1.71 Volts. So the Energy required to light the LED is E = qV or E = -1.6 x 10-19 (1.71) Joule, since a Coulomb-Volt is a Joule. Multiplication of these numbers then gives E = 2.74 x 10-19 Joule.
- 22. Applications Sensor Applications Mobile Applications Sign Applications Automative Uses LED Signals Illuminations Indicators
- 23. Sensor Applications Medical Instrumentation Bar Code Readers Color & Money Sensors Encoders Optical Switches Fiber Optic Communication
- 24. Mobile Applications Mobile Phone PDA's Digital Cameras Lap Tops General Backlighting
- 25. Sign Applications Full Color Video Monochrome Message Boards Traffic/VMS Transportation - Passenger Information
- 26. Automative Applications Interior Lighting - Instrument Panels & Switches, Courtesy Lighting Exterior Lighting - CHMSL, Rear Stop/Turn/Tail Truck/Bus Lighting - Retrofits, New Turn/Tail/Marker Lights
- 27. Signal Appications Traffic Rail Aviation Tower Lights Runway Lights Emergency/Police Vehicle Lighting LEDs offer enormous benefits over traditional incandescent lamps including: Energy savings (up to 85% less power than incandescent) Reduction in maintenance costs Increased visibility in daylight and adverse weather conditions
- 28. Illumination (1/2) Architectural Lighting Signage (Channel Letters) Machine Vision Retail Displays Emergency Lighting (Exit Signs) Neon Replacement Bulb Replacements Flashlights Outdoor Accent Lighting - Pathway, Marker Lights
- 29. Illumination (2/2) LEDs not only consume far less electricity than traditional forms of illumination, resulting in reduced energy costs, but require less maintenance and repair. Studies have shown that the use of LEDs in illumination applications can offer: Greater visual appeal Reduced energy costs Increased attention capture Savings in maintenance and lighting replacements As white LED technology continues to improve, the use of LEDs for general illumination applications will become more prevalent in the industry.
- 30. Indication Household appliances VCR/ DVD/ Stereo and other audio and video devices Toys/Games Instrumentation Security Equipment Switches
- 31. Colours of LEDs (1/3) LEDs are made from gallium-based crystals that contain one or more additional materials such as phosphorous to produce a distinct color. Different LED chip technologies emit light in specific regions of the visible light spectrum and produce different intensity levels. LEDs are available in red, orange, amber, yellow, green, blue and white. Blue and white LEDs are much more expensive than the other colours. The colour of an LED is determined by the semiconductor material, not by the colouring of the 'package' (the plastic body). LEDs of all colours are available in uncoloured packages which may be diffused (milky) or clear (often described as 'water clear'). The coloured packages are also available as diffused (the standard type) or transparent.
- 32. Colours of LEDs (2/3) Tri-colour LEDs The most popular type of tri-colour LED has a red and a green LED combined in one package with three leads. They are called tri- colour because mixed red and green light appears to be yellow and this is produced when both the red and green LEDs are on. The diagram shows the construction of a tri - colour LED. Note the different lengths of the three leads. The centre lead (k) is the common cathode for both LEDs, the outer leads (a1 and a2) are the anodes to the LEDs allowing each one to be lit separately, or both together to give the third colour.
- 33. Colours of LEDs (3/3) Bi-colour LEDs A bi-colour LED has two LEDs wired in 'inverse parallel' (one forwards, one backwards) combined in one package with two leads. Only one of the LEDs can be lit at one time and they are less useful than the tri- colour LEDs described above.
- 34. Comparison Of Chip Technologies For Wide- Angle, Non-Diffused LEDs
- 35. LED Performance (1/8) LED performance is based on a few primary characteristics: Color White light Intensity Eye safety information Visibility Operating Life Voltage/Design Current
- 36. LED Performance (2/8) Colour Peak wavelength is a function of the LED chip material. Although process variations are 賊10 NM, the 565 to 600 NM wavelength spectral region is where the sensitivity level of the human eye is highest. Therefore, it is easier to perceive color variations in yellow and amber LEDs than other colors.
- 37. LED Performance (3/8) White Light When light from all parts of the visible spectrum overlap one another, the additive mixture of colors appears white. However, the eye does not require a mixture of all the colors of the spectrum to perceive white light. Primary colors from the upper, middle, and lower parts of the spectrum (red, green, and blue), when combined, appear white.
- 38. LED Performance (4/8) Intensity LED light output varies with the type of chip, encapsulation, efficiency of individual wafer lots and other variables. Several LED manufacturers use terms such as "super-bright," and "ultra-bright to describe LED intensity. Such terminology is entirely subjective, as there is no industry standard for LED brightness.
- 39. LED Performance (5/8) Eye Safety The need to place eye safety labeling on LED products is dependent upon the product design and the application. Only a few LEDs produce sufficient intensity to require eye safety labeling. However, for eye safety, do not stare into the light beam of any LED at close range
- 40. LED Performance (6/8) Visibility Luminous intensity (Iv) does not represent the total light output from an LED. Both the luminous intensity and the spatial radiation pattern (viewing angle) must be taken into account. If two LEDs have the same luminous intensity value, the lamp with the larger viewing angle will have the higher total light output.
- 41. LED Performance (7/8) Operating Life Because LEDs are solid-state devices they are not subject to catastrophic failure when operated within design parameters. DDP速 LEDs are designed to operate upwards of 100,000 hours at 25属C ambient temperature. Operating life is characterized by the degradation of LED intensity over time. When the LED degrades to half of its original intensity after 100,000 hours it is at the end of its useful life although the LED will continue to operate as output diminishes. Unlike standard incandescent bulbs, DDP速 LEDs resist shock and vibration and can be cycled on and off without excessive degradation.
- 42. LED Performance (8/8) Voltage/Design Current LEDs are current-driven devices, not voltage driven. Although drive current and light output are directly related, exceeding the maximum current rating will produce excessive heat within the LED chip due to excessive power dissipation. The result will be reduced light output and reduced operating life. LEDs that are designed to operate at a specific voltage contain a built-in current-limiting resistor. Additional circuitry may include a protection diode for AC operation or full-bridge rectifier for bipolar operation. The operating current for a particular voltage is designed to maintain LED reliability over its operating life.
- 43. Bargraph 7-segment Starburst Dot matrix Some Types of LEDs
- 49. Preferences http://www.marktechopto.com/ http://acept.la.asu.edu/courses/phs110/expmts/exp13a.html http://www.kpsec.freeuk.com/components/led.htm http://www.fiber-optics.info/articles/LEDs.htm http://www.theledlight.com/technical1.html http://hyperphysics.phy-astr.gsu.edu/hbase/electronic/leds.html www.kpsec.freeuk.com/components/led.htm P.S : You can download this presentation from, http://www.eee.metu.edu.tr/~eekmekci
- 54. Are LEDs Emitting White Light?
- 64. Research Today