�ݺ�ߣ

© Faculty of Engineering, American International University – Bangladesh
Design and Implementation of an Automatic
Irrigation System
Project Group # 55
Under the supervision of
Md. Saniat Rahman Zishan
Assistant Professor
American International University - Bangladesh
Fall Semester 2013-2014
December, 2013
1. Alamgir, Mahzabin 10-16538-2
2. Chowdhury, Alma Taziz 10-16884-2
3 Mollah, Gloria 10-16583-2
4. Mullick, Homaira Amina 09-14880-3

Design and Implementation of an Automatic
Irrigation System
Alamgir, Mahzabin, Mollah, Gloria , Chowdhury, Alma Taziz, Mullick, Homaira Amina
Department of Electrical and Electronic Engineering, American International University-Bangladesh
Abstract— Automation is very important in the advanced
world. Automation makes life more easier, reduces time for
working manually and spontaneous. In an irrigation based
country it is very important to have a developed irrigation
system. This project deals with the automatic operation of the
pump to supply water in the field depending on the soil moisture.
The system can be operated using solar energy or even the DC
voltage converted from AC. This is done by programming in
ATmega328.
Index Terms — Introduction, Solar Tracking Device, Automatic
pump control, Automatic Irrigation System, Simulation,
References, Conclusion.
I. INTRODUCTION
Use of proper method of irrigation is significant in the field
of agriculture. To fulfill this necessity we introduce an
advanced automatic irrigation system. In this automatic system,
we have used sensors, digital circuits, water sources and a
control unit. An ATMEGA328 microcontroller is used which
plays the part to control the whole process of irrigation. It is
programmed to turn on a solenoid when the moisture in the soil
falls below a certain level which is detected by a moisture
sensor. Our circuit implemented, aims to sense and monitor the
irrigation system which in turn makes the entire irrigation
process much more efficient, less time consuming and less
labor intensive. To achieve our goal of a totally automated
farm, we decided to cascade three individual projects and
merge them into one. The three projects in action are:
 An automatic solar tracking device.
 Automatic pump controller.
 Automatic farm irrigation system
II. ARCHITECTURE OF THE SYSTEM
The Automatic Irrigation System is designed in such a way
that irrigation can be done automatically using less labour,
less time and without wasting water. This is done by
merging three different projects into an individual one
where which of them got specific operation in the system.
A. Solar Tracking Device
Solar panels are fitted on the solar tracker. This device
tracks the solar energy following the position of the sun
during the day so that maximum amount of sunlight is
received by the solar panel with the motion of the sun.
Using solar panels increased efficiencies can be achieved. It
is mostly used in remote areas where there is scarcity of
electricity or electrical lines are not situated. The selection
of tracker depends on many factors some of which are
installation size, electric rates, government incentives, land
constraints, latitude, and local weather. The solar tracker
reduces the consumption of electricity with greater
efficiency. This tracker is accompanied with the LDR
variation of resistance and feeds the data to the
microcontroller. The microcontroller sends signal to the
servo motor. The backelite sheet is required to mount the
Light dependant resistors (LDRs). The servo motor shifts
the position of the solar panels as required sensed by the
light dependant resistor (LDR). The LCD display whether
solar energy is generated or not. In this way the solar
tracking device operates.
Figure 2 : Block Diagram of Solar tracker
The block diagram above depicts the behavior of the solar
tracker. The block diagram shows that the power is
supplied to the microcontroller ATMEGA 328. Light
dependant resistor (LDR), servo motor and LCD display
are connected to the microcontroller. As we see, a light
dependent resistor (LDR) senses the position of the sun,
through the variation of resistance and feeds the data to the

microcontroller. The microcontroller sends signal to the
servo motor. The backelite sheet is required to mount the
Light dependant resistors (LDRs). The servo motor shifts
the position of the solar panels as required sensed by the
light dependant resistor (LDR). The LCD display whether
solar energy is generated or not. In this way the solar
tracking device operates.
B. Automatic Pump Controller
Automatic Pump Control system consists of a water
storage, water level detector and indicator, relay, solar
tracker, dc motor and microcontroller. This automatic pump
control can work using two different inputs – solar energy
from Solar tracking device and from main power supply.
The solar tracker will take the solar energy as an input to
the relay that switches it on, switching the pump on to
supply the water to the water storage tank. This can also be
done when there is no solar power. When solar power is
unavailable, that is during night, the power is taken from a
dc motor which gets power from the ac (main) supply. The
switching on of the pump depends on the water level of the
storage. The water level detector has two different levels
set-one of them is maximum or high level and the other is
low or minimum level. When it detects that the water is at
low or minimum level, it will send a signal to the
microcontroller to turn on the pump and supply water to the
storage and according to the level of the water in the
storage, the LEDs will blink which are connected to the
water level indicator. There are three LEDs connected to
the water level indicator. When one LED or no LED glows
then the second relay is switched on to start the pump so
that water starts to fill in the storage and as the water level
increases the rest of the LEDs starts to glow. When all the
LEDs glow, then the relay stops the pump. When the water
level is low the pump is switched on and when the water
level is high the pump is switched off. This is how the
Automatic pump control works as a whole.
Figure: The hardware implementation of the automatic pump
control system.
C. Automatic Farm Irrigation system
The automatic irrigation system consists of the soil
moisture sensor to sense the soil moisture and feed the
input in the microcontroller, the solenoid valve to allow the
water supply to the field depending on the soil moisture
detected, the microcontroller to control all the operations,
the LCD display and the power supply as shown in the
block diagram below.
Figure: Block diagram for the automatic irrigation
system.
The Block diagram of an automatic irrigation system
using moisture sensor is showed above. It consists of a
an Arduino with ATmega328 Microcontroller,
Moisture sensor, solenoid valve , power supply and
LCD Display. At first, the moisture sensor senses the
amount of moisture content in the soil and inputs it to
the microcontroller. Depending on the moisture
content of the soil, it will input the microcontroller to
turn on or turn off the solenoid valve which actually
gives a pressure to turn on the pump and supply water
to the fields. The Moisture level is displayed in the
LCD display.
III.Simulation
Figure: Final simulation.

The diagram shows the full simulation of our project. The
simulation is done using Proteus version 7.8. The simulation
shows the full experimental setup. The project consists of three
parts- Solar tracking device, automatic pump control and
Automatic Irrigation system using Moisture sensor. The Solar
tracker captures the energy from the sun and use it to convert it
generate electricity. This electricity is used to drive the
automatic pump control system. The Automatic pump control
consists of two relays connected in series and a dc motor. The
automatic pump control system can be turned on in two
different ways- using the main supply and using the solar
energy. When the solar power is available then controller uses
the solar power. When it is unavailable then the controller uses
the dc power which is converted from ac supply. The solar
power is in one input of the first relay and the dc power is
connected in the other input. The output of the first relay is
connected as the input of the second relay. The output of water
level detector and indicator also works as an input to the
microcontroller. The water level indicator indicates by lighting
LEDs, that is there are three LEDs attached with the Indicator.
Microcontroller sends the signal to the dc motor accordingly to
switch on or off the pump in the water tank. The soil moisture
sensor senses the soil moisture and informs the microcontroller
to open the solenoid valve which basically is used to give force
to turn on the pump.
IV. Conclusion
Our paper provided the design processes to build a large
system consisting of several individual parts with several
functions. For hardware implementation, proper organizations
had to be made to make the parts to communicate with each
other smoothly with very minimum error. Analysis has been
shown and on the basis of the analysis, proper decisions were
made that required for completely implementing the automatic
irrigation system. The whole system together exhibit numerous
features which can be used in several ways according to need
and thus our designed and implemented automatic irrigation
system is quite user friendly too.
REFERENCES
[1] Automatic Irrigation Based on Soil Moisture for
Vegetable Crops [Online] (Accessed on 10.9.2013)
Available: http://edis.ifas.ufl.edu/pdffiles/ae/ae35400.pdf
[2] Automatic Irrigation systems [Online] (Accessed on
6.8.2013) Available:
http://www.chilliwacktimes.com/news/automatic-
irrigation-systems-1.431180
[3] Sun power signature black solar panels [Online]
(Accessed on 8.10.2013) Available:
http://us.sunpowercorp.com/homes/products-
services/solar-panels/signature-black/
[4] The advantages of water level controller [Online]
(Accessed on 14.10.2013) Available:
http://www.ehow.com/info_8688159_advantages-water-
level-controller.html
[5] Case Study 4, 09 | 2012 Solar powered Vineyard
Irrigation system [Online] (Accessed on 8.10.2013)
Available:
http://www.lorentz.de/pdf/lorentz_casestudy_vineyardlurt
on_chile_en-en.pdf
[6] VH400 Soil moisture sensor probes [Online] (Accessed
on 12.11.2013) Available:
http://www.vegetronix.com/Products/VG400/

�ݺ�ߣ

Summary(group 55)

More Related Content

Summary(group 55)