Narcissus Quagliata developed a new technique for creating fluid glass lines in fused glass works called "light paintings". This was done using a small kiln called the "vitrigraph" designed by Rudi Gritsch. The vitrigraph allows glass to be melted and drawn into lines resembling brush strokes, combining the fluidity of painting with the vibrancy of light in glass. The document describes the construction and use of the vitrigraph kiln, including loading it with glass, recommended firing cycles, and tools that can be used to manipulate the hot glass and create different line effects.
1 of 4
Download to read offline
More Related Content
Technotes 02
1. 1REVISED NOVEMBER 2014
Fused glass is frequently characterized by a cut-and-fit
approach to design. Various shapes of colored glass are cut
and fired to a base blank, often a tile or plate. While this
is a valid method of working the material, it comes more
from a collage or mosaic than a painterly tradition.
Originally trained as a painter, Narcissus Quagliata has
worked in stained glass since the early 1970s. Probably
more than any other modern flat glass artist, Quagliata
has succeeded in imparting the fluidity of a painters
sensibility to leaded glass through both painstaking
selection of unique glasses and a highly expressive use
of the lead line. Invited to take part in the Connections
program of artist exchanges at the Bullseye factory in
1993, Quagliata quickly enlisted the assistance of Rudi
Gritsch, equipment-builder extraordinaire (and at that
time Bullseyes kilnworking director) to devise a way
of generating lines in hot glass that could approximate
the spontaneity of the pen or brush stroke. These glass
lines and the techniques of shading and modeling with
frits became the core of a methodology of fusing that
Quagliata came to call light paintings a revolutionary
approach to working glass in the kiln that combines the
expressiveness of paint with the vibrancy of light.
The key tool in creating these lines is an ingenious small
kiln, designed by Rudi Gritsch, called the vitrigraph.*
Since then Bullseye has built and tested numbers of them,
and sent replicas off to studios around the world. This
article describes the equipment and processes developed
by Quagliata and Gritsch, in the process creating a whole
new vocabulary for fused glass.
Narcissus Quagliata during the creation of Summer Buddha, fused panels
employing hot drawn glass lines.
The Vitrigraph Kiln
Creating a New Vocabulary in Fused Glass
TECHNOTES
A Technical Supplement from Bullseye Glass Co.
2
* From the Latin vitri (glass) and the Greek graph (writing). Not to be
confused with vitreography, the process of making prints from glass plates.
2. 2 TECHNOTES 2
Figure 2
Figure 1
Glass
Figure 3
Caldera Bullseye Edition Kiln specs
Interior: 8 x 8 x 6 3/4 in (20 x 20 x 17 cm)
Exterior: 11 3/4 x 14 x 19 1/2 in (30 x 36 x 50 cm)
Electrical Requirements: 120 V / 15 A
Power Consumption: 1.68 kW
Plug: Standard (NEMA5-15p)
Shipping Weight: 46 lb (21 kg)
Product Number: 8823
Construction of a Linemaking Mini-Kiln
The original vitrigraph kiln was composed of a stack of three
component kiln rings. We now use the Paragon Caldera
because it has a programmable controller (the original did
not), requires less power, and is more versatile. (Figure 1)
To be used as a vitrigraph, the Caldera is set on top of a panel
of 1" (2.5 cm) thick rigidized fiber or vermiculite board that
replaces the bottom of the kiln. This 12" (30.5 cm) square
panel has a 2.5" (6 cm) diameter circle cut out of its center.
The entire unit is mounted overhead either to a wall or on a
sturdy ladder-like structure. Our vitrigraph is mounted with
the bottom about 5'9" (1.75 meters) off the floor. It is, in
essence, a miniature bottomdraw glass furnace. (Figure 2)
Within the heating chamber, a pair of mullite strips (the
same material kiln shelves are made of) bridge the center
opening to support a clay Vitrigraph Pot (8822) 4.5" tall by
5.5" diameter (114 x 140 mm). If purchasing your own, avoid
pots with hairline (or larger) cracks, as these will widen as
they reach molten glass temperatures. In our experience,
unglazed Italian terra cotta pots are more durable. Even
so, these are generally a single use item. A Sentry Xpress
digital temperature controller mounted on the outside of the
kiln controls heating to the kiln chamber. Instructions for
programming this controller are included with the kiln.
Glass Feedstock
Any scrap pieces of Bullseye compatible sheet glass or coarse
(-0003) frit can be melted down to make lines or stringers.
Avoid glass granules smaller than coarse frit, as they produce
a seedier stringer due to the greater amount of air trapped
between the smaller particles.
Loading The Glass
We typically load the glass into the pot outside the kiln, while
it is at room temperature, and then place the loaded pot into
the kiln so that it is supported by the mullite strips. (Figure
3) When working with frit or extremely small pieces of scrap
sheet glass, place a small square of Bullseye compatible sheet
glass the same color as the feedstock over the hole to prevent
the glass from falling out. Then fill the pot with the feedstock.
Firing The Kiln
Before firing the vitrigraph, read the safety notes on page 4.
Make sure that all electrical cords are secured and the kiln
platform youve selected is stable. If your platform doesnt
include a ladder system, youll need a sturdy metal ladder
next to the kiln to access the top lid for charging.
Charging: We advise loading the amount of glass needed
for a run of stringer while the pot is cold, and then cooling
between runs. If time forces you to do continuous melts, or if
3. 3THE VITRIGRAPH KILN
it becomes necessary to add more glass to the pot during the
melt, here are a few things you need to keep in mind:
Turn the power off during charging.
Use extreme care in filling the pot. Glass scraps or
frit which miss the pot and land on the electrical
elements can damage the elements.
Glass scraps or frit that melt against the
refractory brick will corrode it.
Firing cycles and process temperatures for
various glasses: Different types of glasses behave
differently in the melting and forming process. Those
with lower melting temperatures, like Black (000100),
will need to be heated more slowly and to a lower process
temperature to avoid their running too freely. Certain
glasses, like White (000113), will cool more quickly than
others and have a narrower working range. Transparent
cadmium/selenium glasses such as Yellow (001120), Red
(001122), and Orange (001125) have a tendency to opalize
in the remelting process. Only by working with the various
glasses will you come to understand their idiosyncrasies.
Firing the vitrigraph too rapidly may result in a very seedy
melt, with many air bubbles trapped in the resulting
stringers. It may also cause the feedstock to thermal shock,
sending chips and shards into the elements and refractory
bricks. Firing too quickly can also result in an uneven melt,
with the glass in the top of the pot extremely hot and the
glass in the bottom still relatively cold. As a result, the
glass initially flows very slowly before suddenly flowing at
an uncontrollable rate. The following cycle works well to
achieve a very controlled line for most glasses:
RATE (DEGREES/HOUR) TEMPERATURE HOLD
450属F (250属C) 1680-1725属F* (916-941属C) 2:00
*Most transparent glasses and Black (000100) will work well at process
temperatures of 1680属F (916属C). Most opalescent glasses will work well
at process temperatures of 1700属F (927属C). Stiff glasses such as White
(000113) and French Vanilla (000137) work well at 1725属F (941属C).
Depending on your experiences and the types of stringers that you are trying
to create, you will find process temperatures that suit your specific needs.
Forming: During the forming stage the temperature
will determine the quality of line produced. Setting the
kiln at 1680属F (916属C) while melting Black (000100)
should produce a thick, fairly slow-moving stream. At this
temperature it is very easy to manipulate the glass by
handpulling and using the simple tools described below.
Fine-tune the quality of the stream by starting at a low
melting temperature and then slowly increasing it. If the
glass stream is moving so fast that it becomes impossible to
control, turn the kiln off and lift the kiln lid to allow heat to
escape. When the glass is back under control, close the lid
and restart the kiln.
Some Tools and the Line Qualities They Produce
Hand pulling: Many types of lines require only
handwork (while wearing Zetex or Kevlar gloves). If the
glass is viscous enough you can pull it at intervals to
create stringers of fluctuating thickness. At these low
temperatures the glass can also be pulled into curves. At
very high temperatures when the stream is extremely thin
and fast moving you can make delicate birds-nest shapes
by allowing the stream to freefall.
Tongs: If you dont feel comfortable hand-
pulling the stream of glass, there are a
variety of long-handled metal tong-like
tools available, such as the 9" (23 cm) long
hemostat shown here.
Pipes: You can make stringers in the shape of spring-like
coils using a 1" (2.5 cm) diameter steel pipe. These coils can
then be carefully cut into sections that will form perfect
circles when kilnformed. The pipe illustrated here is 15"
(38 cm) long with 0.5" (1 cm) holes drilled through the wall
about 1" (2.5 cm) from the pipes end. Pull the glass stream
through the drilled holes. As the glass flows, twirl it around
the pipe and then cut or break it at the end of the pipe.
Tray: A 2-foot (61 cm) square stainless steel tray held at a
45属 angle about 16 (41 cm) below the bottom of the kiln
makes a good working surface for creating flat curlycues,
S-curves, and other curves.
4. TECHNOTES 2: THE VITRIGRAPH KILN
Melting Cycle and Pot Life
Because of its long working range, Black (000100) is a good
stock for your initial experiments in linemaking. To work in
other colors using the same pot, cycle through the spectrum
so you gradually transition from lighter to darker colors. Any
time you transition from one color to another, the beginning
of the run will produce stringers that have a thin, often
streaky layer of the previous glass on the outer surface. As
the run progresses, this will disappear.
A gray or metallic appearance to the pot after firing is iron in
the clay that has migrated to the surface. This indicates that
the pot (and the glass inside it) became much hotter than it
needed to be.
Note that rapid cooling will also shorten pot life.
Avoid refiring a used pot. The risk of cracking is far greater
than the minimal expense of a new pot. As mentioned
above, watch out for cracks. They widen and eventually
break on firing.
Safety Considerations
Keep the kiln away from flammable surfaces and materials.
Whichever mounting support system you choose, make
sure its sturdy and non-flammable. Any wall brackets
should be firmly connected to structural wall studs.
A freestanding system needs to be properly counter-
balanced so it wont tip over during normal operation.
Use heavy (12 gauge) electrical extension cords. A standard
light-duty cord will overheat and could start a fire.
Make sure that all primary electrical and extension cords
are out of the way and taped down. Taping cords also
protects them from the heat of the kiln and the pulled
stringer, both of which can melt through the insulation and
create a shock and fire danger. If cords are on the floor,
tape them down.
As noted by the manufacturer, the temperature inside the
kiln should never exceed 2350属F (1288属C).
Never leave the kiln unattended, especially above 1500属F
when the glass is starting to soften and flow.
If you charge the kiln using a metal scoop or tool, be certain
to turn off power to the kiln first and avoid contact with
the elements. There is a significant risk of electrical shock
when working with metal tools this close to the
kiln elements.
A piece of sheet metal on the floor directly beneath the kiln
will help prevent a structure fire.
Protective Gear
Safety glasses: A must at all times. Glass will sometimes
thermal shock while being loaded into a preheated pot, and
bits of glass will tend to fly when stringer is broken from the
glass stream.
Gloves: Zetex or Kevlar gloves are necessary for charging
the kiln and for any direct contact with the hot glass.
However, the bulkiness of these gloves makes it difficult to
manipulate the forming tools. A thinner leather glove on the
working hand allows you to handle the tool and provides
some protection from the heat, while a Kevlar glove on the
other hand allows you to break the hot stringer from the
glass stream.
Clothes: Wear cotton pants with long legs and long-sleeved
cotton shirts, and be sure to wear close-toed shoes. Avoid
wearing synthetic materials/fabrics as these are more likely
to catch fire.
息2013,2014BULLSEYEGLASSCO.201341118_KMF8082
bullseyeglass.com
Additional Resources
Vitrigraph Kiln: Basic Use (video lesson)
Drawing with Glass (video lesson)
Featured Products
Paragon Caldera Kiln (8823)
Vitrigraph Base Board (8827)
Vitrigraph Pot (8828)
Vitrigraph Pot, 4 Pack (8816)
Vitrigraph Pot Supports, Set of 4 (8829)