More Related Content
What's hot (19)
Similar to cv (20)
cv
- 1. MUHAMMAD KASHIF JAMIL Permanent Address: House No 284/285 , street water tank Labour Colony Sahiwal Pakistan. Mobile Number: 00923146260564 CNIC No: 36502-1930571-5 Date Of Birth 10 Jan 1988 Email Address:kashif.jamil@yahoo.com Nationality: Pakistani OBJECTIVE Seeking a challenging, development-oriented career within a dynamic and progressive organization where enthusiasm, dedication and the ability to manage tasks effectively are the pre-requisite in driving the organization forward. EDUCATION  B.Sc. Mechanical Engineering (2014) UET Lahore 3.523 /4.0 CGPA  B.TECH (Pass) Mechanical (2010) BZU Multan 82.2%  DAE Mechanical (2007) Govt. Collage of Technology Sahiwal 75.6%  Matric (science ) (2004) Govt. High School Sahiwal 64.588% EXPERIENCE SAIF COMBINE CYCLE POWER PLANT. Operation Supervisor 225MWe ( G.E 6FA G.T & SST900 STG) May 2009 to 14TH Oct 2010 Worked on commissioning of GE Gas turbines and Siemens Steam Turbine of Combine Cycle Power Plant. Project is commissioned successfully, later on activities along with G.E energy O&M team  Control room operations i.e. switching, controlling, operation.  Maintaining shift Log, reading sheets, local control room operations and field operations.  Use of Computer based maintenance management system i.e. 1- Maximo version 6.0  Supervised Startup and shut down of complex.  Operate complex under technical limits.  Heat recovery steam generator Nooter Ericson (125*2 T/H)  Mark-VI control system for Gas Turbines.  Siematic PCS-7 DCS control of Siemens steam turbine.  PACiS HMI for power distribution control make AREVA.  DCS control Baily infi 90 system for HRSGs and Balance of plant make ABB.  BOP system i.e. Water bath heater for gas heating, Deep well turbine pumps network, Air compressor, auxiliary Boiler, De-mineralized Water Treatment Plant (RO type),  Switching of 132kv Gas Insulated Switchgear (GIS).  Carried out all plant capacity test i.e. initial capacity test, reliability test, performance test, etc  Fully involves in the plant startup, plant normal power operation, power reduction and handling all types of transients in all phases of plant.  System Line up, Isolation, normalization & Priming Of systems CENTURY PAPER & BOARD MILLS. Trainee Technician Power Plant Department Oct 2007 to March 2008  Maintenance all types of valve , replacing gaskit , Lube oil and inspection.  All type strainer checking and replacing  Vibration analysis measurement and condoning monitoring  Use of Computer based maintenance management system TELE TOWER –PROJECTED BY IKAN Supervisor Manufacturing Department July 2007 to Oct 2007  Arc and gas welding inspection and Legs Operation Limit checking  Ladder galvanizing , Modification of components in CAD
- 2.  Mechanical workshop under all the mechanical operation related to tower . INTERNSHIP Dawood Hercules fertilizers(1 month) Departments: (Planning section, Equipment section, Machinery section, Workshop section)  Valves (NRV’S, PRV,S, PSV’S, Gate, plug, globe etc),gaskets and their function,  Maintenance planning, knowledge about MWR and work permit  Balancing of parts(dynamic balancing, rotors of turbines and any other parts  presentation on understanding of valves (at DH plant) & presenting to incharges and respective Engineers. Qadirpur Gas Field OGDCL ( One Week )  Gained a lot of practical knowledge about valves (NRV’S, PRV,S, PSV’S, Gate, plug, globe etc),gaskets and their function, maintenance planning, knowledge  Vibration analysis techniques and special working on taking vibrations of cooling tower , compressors , motors, and boroscopy of gas turbine . PROJECTS FINAL YEAR PROJECT Working on Reliability Centered Maintenance (RCM ) Implementation on feed water pump at Baloki 225 MW, in UET LHR. ( BSc Engineering )  Maintenance and its technique  RCM and its criticality on bases of RPN No  FMECA  Cost Evaluation ACADMIC PROJECTS  Design and manufacturing the heat exchanger (ASME Technical Project Competition) TECHNICAL AND EHS Training MARK V1  Certificate of MARK V1 control system for 6FA G.E gas turbine. SISMENS SST 900  Certificate OF Operation and control of SISMENS SST 900 steam turbine. CMEC SGS  PLANT system training from china machinery export company CMEC.  Inspection ,measurement and testing Maximo version 6.0 EHS  Responsible for authorization of work permit  One Month on EHS Procedure of GE  Firefighting, LOTO, First aid, PPE awareness, chemical spill etc.  Three days First Aid Training by Red Crescent Society of Pakistan. GE on line training  32 On line Technical and EHS training through GE online learning program E-learning essential for every employee, also attend refresher courses. COMPUTER SKILLS 1-Auto CAD 2- Solid Edge 3- Microsoft office 4- CNC Lathe 5-MAT Lab 6-Primavera 7- ANSYS 8-FPWIN Pro 5 SHORT COURSES 1- Safety/Risk Management 2- Auto Cad 3- CNC Lathe 4- AHM( Assets Health Management ) DISTINCTIONS 1- I got 2nd position in B.Tech (pass) Mechanical Technology ,securing 1195/1450. 2- I was the group leader of my final year project. PERSONAL SKILLS  Working as a leader in Final Year Project in B.Tech (pass)  Creative, self-motivated with strong interpersonal skills, always ready to tackle the problems  Excellent communication skills and leadership qualities, team man  Swiftto adapt changes according to the working conditions. EXTRACURRICULAR ACTIVITIES  I was the captain of my hostel cricket team so it added to my leadership qualities.  Reading, cooking, playing games on PC  Running, jogging, swimming