ECT Textile
1 like260 views
This document summarizes the installation of an energy conservation turbine (ECT) at a textile plant in India to recover energy from steam throttling. The 360 kW ECT was installed in July 2015 at Durga Polyester to generate power from steam exiting at 3.5 bar(g) after entering at 11.5 bar(g). It generates over 2.85 million kWh annually, saving $190,000 per year with a payback period of less than 2 years. The ECT improves process efficiency while reducing carbon footprint and energy costs.
1 of 5
Recommended
Ect concentrated-solar
Ect concentrated-solarcircuscreative
油
This document discusses the supply, commissioning, and testing of a 3000 kW turbine for a concentrated solar power plant owned by Atria Power Corporation. The turbine runs on solar energy and generates 3000 kW of power at 415 V and 50 Hz to feed into the local grid. It is an extraction-cum-condensing turbine with a turbine inlet pressure of 34 bar(g) and temperature of 350 degrees C. Using the turbine is expected to generate annual savings of $1.8 million and pay for itself within one year, while also providing environmental benefits like reduced carbon emissions.Ect captive-power
Ect captive-powercircuscreative
油
This document discusses the installation of a 425 kW energy conservation turbine (ECT) at the captive power plant of Ballarpur Industries Limited, one of the largest paper producers in the region. The ECT was installed in parallel with the pressure reducing valve upstream of the deaerator to generate power from steam throttling. Over its expected 15 year lifetime, the ECT is projected to save $3.4 million in capital costs with a payback period of less than 2 years, while also improving process efficiency and reducing the plant's carbon footprint and energy consumption.Ect dielsel-engine-whr-gmr
Ect dielsel-engine-whr-gmrcircuscreative
油
This document discusses a waste heat recovery turbine project at a 200 MW diesel engine power plant in Chennai, India. The plant recovers heat from engine exhaust using a heat recovery steam generator and steam turbine to generate 600 kW of additional power. Installed in 2011, the turbine saves $300,000 per year in energy costs and will save $4.5 million over its 15-year lifetime. The project has an payback period of less than 2 years and provides environmental benefits like reduced carbon emissions.Ect chemical
Ect chemicalcircuscreative
油
This document discusses the installation of an energy conservation turbine (ECT) at a chemical manufacturing plant to recover energy from steam throttling. The 90 kW ECT was installed in 2011 to utilize steam from the plant's formaldehyde and hexamine production processes. It generates 90 kW of power from 8 tons per hour of steam at 241 degrees C and 22 bar pressure, saving an estimated $60,000 per year in energy costs. The project pays for itself in under 2 years and provides environmental benefits such as reduced carbon emissions and process efficiency improvements over the turbine's 15-year lifetime.The PowerStack powerpoint
The PowerStack powerpoint45 innovations
油
This document describes a wind power system that harnesses kinetic energy from vehicle exhaust to generate electricity without relying directly on wind. It has undergone alpha and beta prototyping, with the beta prototype proving successful in a field test without noted side effects. The system can provide off-grid or on-grid power ranging from 1-50kW depending on the size of the vehicle exhaust source, and has potential environmental benefits through reduced greenhouse gas emissions. ECT in Captive Power Plants of process industries
ECT in Captive Power Plants of process industriesShreyas Krishna
油
This document discusses the installation of a 425 kW turbine by TurboTech Precision Engineering at the captive power plant of Ballarpur Industries Limited (BILT) in Maharashtra, India. BILT operates a 60 MW thermal power plant to provide steam and power for its large-scale paper manufacturing facility. The installed turbine utilizes low pressure extraction steam to generate 425 kW of additional power. This has resulted in estimated energy savings of 136 lakh kWh and cost savings of 5.44 crore rupees over the past 4 years since installation. The turbine also supports environmental efforts by reducing 18,000 tons of carbon dioxide emissions compared to burning fossil fuels for the same power generation.STORETEC CASE STUDY
STORETEC CASE STUDYMartin Dowd Commercial Solar PV Consultant
油
This document summarizes a commercial roof-mounted solar installation project in Tibshelf, Derbyshire. An 83.5 kWp solar photovoltaic system was installed on the roof of Storetec UK, consisting of 334 solar panels. The system was expected to generate 67,000 kWh annually and provide Storetec with an excellent 13.5% return on investment. The installation was carried out by GYO Energy and helps Storetec reduce their carbon footprint while their customers increasingly focus on environmental impacts.Leaflet Plug&Sun and Plug&Sun+ EN
Leaflet Plug&Sun and Plug&Sun+ ENTomaso Charlemont
油
The document describes Plug&Sun systems, which are fully integrated solar energy solutions for off-grid and poor grid applications ranging from 1 kW to 1 MW. The systems use concentrated photovoltaic modules from Soitec that are 32% efficient and use dual-axis tracking to reduce energy losses compared to standard photovoltaic panels. The Plug&Sun systems provide clean, efficient electricity for various uses with no fuel consumption, noise, or carbon dioxide emissions.NSW ggas scheme summary
NSW ggas scheme summaryAGL Energy Limited
油
Retailers in NSW are required to reduce emissions to 7.27 tonnes per capita by 2007. Each retailer's allowable emissions are determined by their market share multiplied by the overall emission target. If a retailer's emissions are higher than their benchmark, they can purchase emission reduction certificates to meet their benchmark. NGACs represent 1 tonne of abatement and can be created through lower emission generation, demand reductions, abatement by large users, and carbon sequestration. Once a national emissions trading scheme is established, GGAS will transition to the ETS.Questionnaire PSSP Program
Questionnaire PSSP ProgramAvish Thakral
油
This document is a pre-audit questionnaire for a filling station seeking to install a solar photovoltaic system through a government program. It requests information on the station's current electricity load and usage, available roof space for solar panels, recent electricity bills, diesel generator use and costs, existing backup systems, preferred loads to power with solar, and motivations and financing preferences for the solar installation. The filling station must provide details like installed lighting and cooling loads, hours of power outages, diesel generator and maintenance costs, and inverter and battery specifications if already in use.SYKES TIMBER CASE STUDY
SYKES TIMBER CASE STUDYMartin Dowd Commercial Solar PV Consultant
油
This document summarizes a 64.25 kWp solar PV system installed at Sykes Timber in Atherstone, Warwickshire by GYO Energy. The system consists of 257 solar panels mounted on 3 buildings and is predicted to generate 54,500 kWh annually. It provides Sykes Timber with an excellent 14.8% return on investment while offsetting 38 tons of CO2 emissions per year.RCREEE-enerMENA_Tunisa development 
RCREEE-enerMENA_Tunisa development RCREEE
油
Renewable Energy for Project Planners and Managers:enerMENA Professional Training Course for CSP
19-23 August,2013
Cairo, Egypt.ESCO Contracting - CII Danfoss, Chennai Aug 2017
ESCO Contracting - CII Danfoss, Chennai Aug 2017Aspiration Cleantech Ventures
油
This document summarizes an energy efficiency case study by Aspiration Cleantech Ventures for one of their automotive component manufacturing clients. Currently, the client uses kerosene to provide process heat between 85-90属C for cleaning components. Aspiration proposes installing a 186 kW heat pump to provide this heat more efficiently. Using the heat pump would save the client Rs. 6.55 crores over 10 years in fuel costs compared to continuing with kerosene. The summary outlines the client's current energy usage and costs, the technical specifications of the proposed heat pump solution, and the expected economic and environmental benefits of switching to the more efficient technology.A3 - Financing geothermal development: Decreasing equity requirements 
A3 - Financing geothermal development: Decreasing equity requirements Iceland Geothermal
油
- Green Energy Geothermal provides modular geothermal wellhead power plants that are faster and lower cost to develop than traditional large-scale geothermal power plants.
- An independent case study found that developing the same 110MW project using GEG's modular wellhead plants requiring $100M less equity, could generate power 1.5 years earlier, and provide a 6.4% higher investor return than the conventional approach.
- GEG has successfully commissioned 15 geothermal wellhead plants totaling 81.1MW in Kenya and provides turnkey solutions globally.SiS Csiro Energy Centre Mc Gregor 2007
SiS Csiro Energy Centre Mc Gregor 2007guestb40d60
油
The CSIRO Energy Centre in Australia has various sustainable energy features that reduce its environmental impact. It uses 950 MWh of electricity and 225,700 MJ of natural gas annually. Distributed generation systems produce 780 MWh of electricity annually. Passive design maximizes natural lighting and ventilation to reduce energy use. Underfloor air conditioning and optimal siting lower emissions by 262,640 kgCO2e and 75,000 kgCO2e annually compared to conventional designs. The building has won several awards for its sustainability.Burns Mc Donnell coal symposium recip engines
Burns Mc Donnell coal symposium recip enginesvranalletta
油
This document discusses reciprocating engines and natural gas engine generators. It notes that reciprocating engines can provide 10 MW of power capacity with a 20-40% capacity factor, good part load heat rate, black start capability within 5 minutes, and reactive power and frequency support. It lists some manufacturers that make natural gas engine generators between 3.6-9.3 MW. Reciprocating engines are needed because the sun doesn't always shine and the wind doesn't always blow. Benefits of natural gas engine power projects include multiple shafts, minimal degradation from air temperature or altitude, near zero water usage with radiator cooling, and combined heat and power potential. Examples of large scale natural gas reciprocating engine plants are shown onGrid connected rooftop solar power plant at silicon
Grid connected rooftop solar power plant at siliconNavneet Das
油
The presentation tells about the ratings of solar components, the energy produced and also its utility in Silicon Institute Of Technology.Energy management and cost optimization using solar energy 
Energy management and cost optimization using solar energy Sudipta Ambal
油
Generating energy that produces no greenhouse gas emissions from fossil fuels and reduces some types of air pollution. To reduce our daily to daily increasing electricity bill cost. Creating economic development and jobs in manufacturing, installation, etc.solar energy
solar energyuday kiran dokala
油
The document outlines how to become an entrepreneur in the solar energy sector in India. It discusses the working of solar plants, requirements like land and funding options. It also addresses distributing generated power, necessary government permissions, problems faced by solar plants like dust accumulation, and recommendations such as improving solar panel lifetime through research funding. The goal is to reduce carbon emissions from coal power through increased solar power capacity.Smart Grid
Smart GridEmTech
油
1) The document discusses various energy priorities and scenarios in India including increasing renewable energy sources like wind and solar while reducing pollution.
2) It provides an overview of smart grid technologies and their benefits in distributing power more efficiently while integrating renewables.
3) GE is working on enhancing its wind and biomass technologies as well as leveraging opportunities in gas energy to support India's energy needs and climate goals.H2 fuel cells future alternative
H2 fuel cells future alternativeAshish Chauhan
油
H2 Fuel cell based on PEM technology can be used to utilize the vent H2 . A case study is discussed in this PPTSolar Energy Applications
Solar Energy ApplicationsAvish Thakral
油
This document discusses using solar photovoltaic panels to generate and store power for backup use during power outages or in areas without grid access. It provides examples of roof-top solar installations for residential, commercial, industrial and other applications. The benefits listed are reduced dependence on diesel fuel, almost zero maintenance, a silent and pollution-free power source, and utilizing unused roof space. Cost analyses are provided comparing solar to diesel generation. The company promotes solar solutions and provides installation and maintenance services.Rooftop Solar System in Raheja Eternity, Mumbai
Rooftop Solar System in Raheja Eternity, MumbaiADDA
油
The Raheja Eternity Housing Society initiated several energy conservation and renewable energy projects from December 2016 to September 2017 to reduce their high energy consumption and bills. They replaced over 600 lights with LED bulbs, installed 55 motion sensors, and implemented a two-phase rooftop solar system totaling 81.5 kW. These measures reduced their monthly energy consumption by 74% from 25,900 to 6,800 units and lowered their energy bill by 94% from Rs. 3,59,280 to Rs. 20,000. The projects also decreased their CO2 emissions by 66% and contributed to a 78% reduction in monthly maintenance fees.Solarcool Innovation Brochure
Solarcool Innovation BrochureRohan Dinn
油
SolarCool provides innovative solar thermal solutions for commercial businesses to reduce energy consumption and costs. Their solutions include retrofitting solar panels and collection units to existing refrigeration, HVAC, and chiller systems to boost their efficiency. Case studies report efficiency increases of over 50% according to clients like Cable & Wireless, with one system achieving 63% efficiency. SolarCool also offers funding programs to cover the costs of their green technology solutions.AS3 cop-21_US
AS3 cop-21_USAlex Roustaei
油
This feasibility study examines a proposed solar self-consumption project for a building called the "House of Enterprises" in Villeneuve-la-Garenne, France. The building currently has high electricity consumption of around 154 MWh per year. A photovoltaic system with two fields totaling 260 square meters would generate an estimated 56 MWh of electricity annually, enough to cover 35% of the building's needs on average. However, the financial analysis shows that with an investment of 240,000, the savings from avoided electricity costs over the system's lifetime would not offset the upfront costs. For the project to be economically viable, energy efficiency upgrades would need to lower the building's consumption first. Currently,Oem business presentation introduction jan 2017
Oem business presentation introduction jan 2017Dan Nadav
油
Qnergy is growing its OEM business where innovative companies design and manufacture advanced solutions based on our maintenance-free Generator. For further details please contact us at info@qnergy.com or at +1 775 247 1316. Phillips Ch10 Ppt 1
Phillips Ch10 Ppt 1Jeffrey Phillips
油
A brief overview of the cost drivers for CO2 capture from coal power plants and what can be done to decrease those costs.Playing Well with Others - Market for Storage Hybrids
Playing Well with Others - Market for Storage HybridsJill Kirkpatrick
油
With 93% of H1 2018 installations in the U.S. being paired solar, hybrid systems are increasingly emerging into the midstream of the energy storage industry. Potential operational benefits and revenue streams are clearly outpacing existing regulations. This research presentation will explore the potential value of hybrid systems and the policies needed to incentivize them, such as Clean Peak standards, and will be followed by a 2-minute Q&A.
Ect kraft-paper
Ect kraft-papercircuscreative
油
The document discusses the installation of a 550 kW energy conservation turbine (ECT) at a paper manufacturing plant in the United Arab Emirates. The ECT was installed in 2006 parallel to the steam header to recover energy from throttling steam. It generates 550 kW of power from 20 tons per hour of steam and saves the plant over $530,000 per year in energy costs. Over the turbine's 15-year lifespan, the total capital savings are estimated to be $7.9 million. The project achieved a payback period of less than one year and provides environmental benefits like reduced carbon emissions and improved process efficiency.Turbo tech presentation for ECT in kraft paper manufacturing plant
Turbo tech presentation for ECT in kraft paper manufacturing plantShreyas Krishna
油
TurboTech Precision Engineering supplied and commissioned a 550 kW turbine for a recycled paper manufacturing plant in Dubai called Union Paper Mill. The plant uses waste paper as its primary raw material to produce fluting, test liner, and core board. The mini steam turbine was installed parallel to the pressure relief valve downstream of the process boiler. It has a design inlet pressure of 16 bar and inlet temperature of 204 degrees C, producing 550 kW of power. Over its seven years of operation, the turbine has helped the plant achieve estimated energy savings of 40 lakh units per year and total cost savings of 5.6 crore rupees, while preventing the release of 28,000 tons of carbon dioxide into the atmosphere.More Related Content
What's hot (20)
NSW ggas scheme summary
NSW ggas scheme summaryAGL Energy Limited
油
Retailers in NSW are required to reduce emissions to 7.27 tonnes per capita by 2007. Each retailer's allowable emissions are determined by their market share multiplied by the overall emission target. If a retailer's emissions are higher than their benchmark, they can purchase emission reduction certificates to meet their benchmark. NGACs represent 1 tonne of abatement and can be created through lower emission generation, demand reductions, abatement by large users, and carbon sequestration. Once a national emissions trading scheme is established, GGAS will transition to the ETS.Questionnaire PSSP Program
Questionnaire PSSP ProgramAvish Thakral
油
This document is a pre-audit questionnaire for a filling station seeking to install a solar photovoltaic system through a government program. It requests information on the station's current electricity load and usage, available roof space for solar panels, recent electricity bills, diesel generator use and costs, existing backup systems, preferred loads to power with solar, and motivations and financing preferences for the solar installation. The filling station must provide details like installed lighting and cooling loads, hours of power outages, diesel generator and maintenance costs, and inverter and battery specifications if already in use.SYKES TIMBER CASE STUDY
SYKES TIMBER CASE STUDYMartin Dowd Commercial Solar PV Consultant
油
This document summarizes a 64.25 kWp solar PV system installed at Sykes Timber in Atherstone, Warwickshire by GYO Energy. The system consists of 257 solar panels mounted on 3 buildings and is predicted to generate 54,500 kWh annually. It provides Sykes Timber with an excellent 14.8% return on investment while offsetting 38 tons of CO2 emissions per year.RCREEE-enerMENA_Tunisa development
RCREEE-enerMENA_Tunisa development RCREEE
油
Renewable Energy for Project Planners and Managers:enerMENA Professional Training Course for CSP
19-23 August,2013
Cairo, Egypt.ESCO Contracting - CII Danfoss, Chennai Aug 2017
ESCO Contracting - CII Danfoss, Chennai Aug 2017Aspiration Cleantech Ventures
油
This document summarizes an energy efficiency case study by Aspiration Cleantech Ventures for one of their automotive component manufacturing clients. Currently, the client uses kerosene to provide process heat between 85-90属C for cleaning components. Aspiration proposes installing a 186 kW heat pump to provide this heat more efficiently. Using the heat pump would save the client Rs. 6.55 crores over 10 years in fuel costs compared to continuing with kerosene. The summary outlines the client's current energy usage and costs, the technical specifications of the proposed heat pump solution, and the expected economic and environmental benefits of switching to the more efficient technology.A3 - Financing geothermal development: Decreasing equity requirements
A3 - Financing geothermal development: Decreasing equity requirements Iceland Geothermal
油
- Green Energy Geothermal provides modular geothermal wellhead power plants that are faster and lower cost to develop than traditional large-scale geothermal power plants.
- An independent case study found that developing the same 110MW project using GEG's modular wellhead plants requiring $100M less equity, could generate power 1.5 years earlier, and provide a 6.4% higher investor return than the conventional approach.
- GEG has successfully commissioned 15 geothermal wellhead plants totaling 81.1MW in Kenya and provides turnkey solutions globally.SiS Csiro Energy Centre Mc Gregor 2007
SiS Csiro Energy Centre Mc Gregor 2007guestb40d60
油
The CSIRO Energy Centre in Australia has various sustainable energy features that reduce its environmental impact. It uses 950 MWh of electricity and 225,700 MJ of natural gas annually. Distributed generation systems produce 780 MWh of electricity annually. Passive design maximizes natural lighting and ventilation to reduce energy use. Underfloor air conditioning and optimal siting lower emissions by 262,640 kgCO2e and 75,000 kgCO2e annually compared to conventional designs. The building has won several awards for its sustainability.Burns Mc Donnell coal symposium recip engines
Burns Mc Donnell coal symposium recip enginesvranalletta
油
This document discusses reciprocating engines and natural gas engine generators. It notes that reciprocating engines can provide 10 MW of power capacity with a 20-40% capacity factor, good part load heat rate, black start capability within 5 minutes, and reactive power and frequency support. It lists some manufacturers that make natural gas engine generators between 3.6-9.3 MW. Reciprocating engines are needed because the sun doesn't always shine and the wind doesn't always blow. Benefits of natural gas engine power projects include multiple shafts, minimal degradation from air temperature or altitude, near zero water usage with radiator cooling, and combined heat and power potential. Examples of large scale natural gas reciprocating engine plants are shown onGrid connected rooftop solar power plant at silicon
Grid connected rooftop solar power plant at siliconNavneet Das
油
The presentation tells about the ratings of solar components, the energy produced and also its utility in Silicon Institute Of Technology.Energy management and cost optimization using solar energy
Energy management and cost optimization using solar energy Sudipta Ambal
油
Generating energy that produces no greenhouse gas emissions from fossil fuels and reduces some types of air pollution. To reduce our daily to daily increasing electricity bill cost. Creating economic development and jobs in manufacturing, installation, etc.solar energy
solar energyuday kiran dokala
油
The document outlines how to become an entrepreneur in the solar energy sector in India. It discusses the working of solar plants, requirements like land and funding options. It also addresses distributing generated power, necessary government permissions, problems faced by solar plants like dust accumulation, and recommendations such as improving solar panel lifetime through research funding. The goal is to reduce carbon emissions from coal power through increased solar power capacity.Smart Grid
Smart GridEmTech
油
1) The document discusses various energy priorities and scenarios in India including increasing renewable energy sources like wind and solar while reducing pollution.
2) It provides an overview of smart grid technologies and their benefits in distributing power more efficiently while integrating renewables.
3) GE is working on enhancing its wind and biomass technologies as well as leveraging opportunities in gas energy to support India's energy needs and climate goals.H2 fuel cells future alternative
H2 fuel cells future alternativeAshish Chauhan
油
H2 Fuel cell based on PEM technology can be used to utilize the vent H2 . A case study is discussed in this PPTSolar Energy Applications
Solar Energy ApplicationsAvish Thakral
油
This document discusses using solar photovoltaic panels to generate and store power for backup use during power outages or in areas without grid access. It provides examples of roof-top solar installations for residential, commercial, industrial and other applications. The benefits listed are reduced dependence on diesel fuel, almost zero maintenance, a silent and pollution-free power source, and utilizing unused roof space. Cost analyses are provided comparing solar to diesel generation. The company promotes solar solutions and provides installation and maintenance services.Rooftop Solar System in Raheja Eternity, Mumbai
Rooftop Solar System in Raheja Eternity, MumbaiADDA
油
The Raheja Eternity Housing Society initiated several energy conservation and renewable energy projects from December 2016 to September 2017 to reduce their high energy consumption and bills. They replaced over 600 lights with LED bulbs, installed 55 motion sensors, and implemented a two-phase rooftop solar system totaling 81.5 kW. These measures reduced their monthly energy consumption by 74% from 25,900 to 6,800 units and lowered their energy bill by 94% from Rs. 3,59,280 to Rs. 20,000. The projects also decreased their CO2 emissions by 66% and contributed to a 78% reduction in monthly maintenance fees.Solarcool Innovation Brochure
Solarcool Innovation BrochureRohan Dinn
油
SolarCool provides innovative solar thermal solutions for commercial businesses to reduce energy consumption and costs. Their solutions include retrofitting solar panels and collection units to existing refrigeration, HVAC, and chiller systems to boost their efficiency. Case studies report efficiency increases of over 50% according to clients like Cable & Wireless, with one system achieving 63% efficiency. SolarCool also offers funding programs to cover the costs of their green technology solutions.AS3 cop-21_US
AS3 cop-21_USAlex Roustaei
油
This feasibility study examines a proposed solar self-consumption project for a building called the "House of Enterprises" in Villeneuve-la-Garenne, France. The building currently has high electricity consumption of around 154 MWh per year. A photovoltaic system with two fields totaling 260 square meters would generate an estimated 56 MWh of electricity annually, enough to cover 35% of the building's needs on average. However, the financial analysis shows that with an investment of 240,000, the savings from avoided electricity costs over the system's lifetime would not offset the upfront costs. For the project to be economically viable, energy efficiency upgrades would need to lower the building's consumption first. Currently,Oem business presentation introduction jan 2017
Oem business presentation introduction jan 2017Dan Nadav
油
Qnergy is growing its OEM business where innovative companies design and manufacture advanced solutions based on our maintenance-free Generator. For further details please contact us at info@qnergy.com or at +1 775 247 1316. Phillips Ch10 Ppt 1
Phillips Ch10 Ppt 1Jeffrey Phillips
油
A brief overview of the cost drivers for CO2 capture from coal power plants and what can be done to decrease those costs.Playing Well with Others - Market for Storage Hybrids
Playing Well with Others - Market for Storage HybridsJill Kirkpatrick
油
With 93% of H1 2018 installations in the U.S. being paired solar, hybrid systems are increasingly emerging into the midstream of the energy storage industry. Potential operational benefits and revenue streams are clearly outpacing existing regulations. This research presentation will explore the potential value of hybrid systems and the policies needed to incentivize them, such as Clean Peak standards, and will be followed by a 2-minute Q&A.
Similar to ECT Textile (20)
Ect kraft-paper
Ect kraft-papercircuscreative
油
The document discusses the installation of a 550 kW energy conservation turbine (ECT) at a paper manufacturing plant in the United Arab Emirates. The ECT was installed in 2006 parallel to the steam header to recover energy from throttling steam. It generates 550 kW of power from 20 tons per hour of steam and saves the plant over $530,000 per year in energy costs. Over the turbine's 15-year lifespan, the total capital savings are estimated to be $7.9 million. The project achieved a payback period of less than one year and provides environmental benefits like reduced carbon emissions and improved process efficiency.Turbo tech presentation for ECT in kraft paper manufacturing plant
Turbo tech presentation for ECT in kraft paper manufacturing plantShreyas Krishna
油
TurboTech Precision Engineering supplied and commissioned a 550 kW turbine for a recycled paper manufacturing plant in Dubai called Union Paper Mill. The plant uses waste paper as its primary raw material to produce fluting, test liner, and core board. The mini steam turbine was installed parallel to the pressure relief valve downstream of the process boiler. It has a design inlet pressure of 16 bar and inlet temperature of 204 degrees C, producing 550 kW of power. Over its seven years of operation, the turbine has helped the plant achieve estimated energy savings of 40 lakh units per year and total cost savings of 5.6 crore rupees, while preventing the release of 28,000 tons of carbon dioxide into the atmosphere.Sustainable Energy Solutions for reducing CO2 emissions | VigilantPlant
Sustainable Energy Solutions for reducing CO2 emissions | VigilantPlantYokogawa
油
Yokogawa is committed to sustaining your business, the environment, and the society that we all are a part of.
We are doing this by developing more energy-efficient technology, helping operations produce a smaller
carbon footprint, and building rock solid products that protect our environment from contaminants.
Sustainability is not just a job for Yokogawa but for all industry.
Power LifeMax* - Solutions for B/E Gas Turbine Fleet
Power LifeMax* - Solutions for B/E Gas Turbine FleetGE_India
油
- GE has over 40 years of experience with B/E gas turbine technology and has installed over 3,000 units globally totaling over 224 GW of power.
- GE offers Power LifeMax solutions to maximize the performance and value of mature gas turbine fleets, including the Advanced Gas Path and 9E Max upgrades.
- The Advanced Gas Path upgrade improves heat rate by 1.5% for combined cycle and 1.7% for simple cycle while increasing output by 3.8% for combined cycle and 3.6% for simple cycle. It has over 29,000 fired hours of experience across 8 units.
- The 9E Max upgrade further improves performance with a 6% reduction to combined cycle heat rate
Polymer Processing Cost Saving Workshop - 03 Sustainable Development
Polymer Processing Cost Saving Workshop - 03 Sustainable DevelopmentInvest Northern Ireland
油
(1) This document discusses opportunities for reducing costs through improving energy efficiency in polymer processing. It identifies areas of high energy consumption and potential savings.
(2) Extruders and heating processes account for over 60% of energy usage on average. The document analyzes specific energy usage for an example extruder process and estimates potential savings of 17% through measures like heat recovery.
(3) Government schemes provide funding support for energy audits, loans, grants, and renewable energy projects to help businesses implement efficiency improvements and reductions in operating costs. Upcoming events are noted to further engage the polymer sector on sustainability.Renewable Energy From Municipal Solid Waste And Automobile Shredder Residues
Renewable Energy From Municipal Solid Waste And Automobile Shredder ResiduesJaapaz
油
A chemical process which utilizes CO2 and CO to oxidize carbon contained in waste to a coal equivalent form of fuel. This exothermic reaction preserves the metals contained and prevents the formation of harmful pollutants such as dioxins and furans. Amber kinetics intro non nda 06-16-2017
Amber kinetics intro non nda 06-16-2017仍亳亰舒于亠舒 弌舒仂于亠仂于舒
油
This document summarizes Amber Kinetics' flywheel energy storage technology. It describes their 4-hour duration flywheel system for utility-scale applications, which is a significant increase over existing 1-15 minute flywheel technologies. It provides specifications for Amber's Model 32 flywheel, outlines the technology's advantages over chemical batteries, and shows it has the lowest 20-year total cost of ownership compared to other storage options. The document also summarizes Amber Kinetics' company milestones, product roadmap, and commercial projects.The economics of reducing the cost of energy by 13% revenues
The economics of reducing the cost of energy by 13% revenuesSentient Science
油
At what speed is your digitalization effort? There is no dispute, digitalization will play a key role in improving the sustainability of renewable energy sources through efficiency. The question remains Where are you? While the industry has embraced the importance, water cooler conversations continue - How to monetize the true value of the data from digitalization?
The webinar outlines:
How digitalization is applied across all corporate business units: asset management, operations management, risk management and supply chain management to reduce the cost of energy by up to 13%
An industry operator case study on monetizing your digitalization efforts and understand the true ROI
A digitalization value statement to enable operations management can provide a short-term watch list from 0-12 months enabling early detection prior to consequential damage beyond an operator's current capabilities attributes to 2-3% of cost avoidance or cost savings.Lab 6
Lab 6Jasmit Kalra
油
Tegtora Systems uses thermoelectric generators (TEGs) to generate clean energy from waste heat produced by heavy industrial plants like cement manufacturing facilities. Each TEG installation could generate over 300,000 kWh of electricity annually and provide a 3-year return on investment by offsetting electricity costs and reducing carbon emissions. Tegtora's first product, called Tegtora Prime, leverages high temperatures from cement kilns to power TEGs installed on the external shell, validating the technology with a leading cement producer.Cogeneration
CogenerationPinaki Bhadury
油
Cogeneration, or combined heat and power (CHP), involves generating electricity and useful thermal energy from a single fuel source. This is more efficient than separate generation of power and heat, with overall efficiencies potentially over 75%. Cogeneration can reduce fuel costs by 40-50% and lower carbon dioxide emissions. It provides reliable, lower cost power for industrial processes and other applications like district heating. Widespread adoption of cogeneration could cut India's fuel use and greenhouse gas emissions significantly.DynGlobal DG Power Panels B
DynGlobal DG Power Panels BVern Wright
油
The document discusses DynGlobal's solar panel systems for powering transportation equipment. It describes their 800W and 400W solar panels and notes their durability, efficiency over 20%, and ability to be arranged in series or parallel. It then summarizes the potential return on investment for using the solar panels on refrigerated trailers based on applicable US federal tax incentives for solar energy systems, which allow for a 30% tax credit in the first year and accelerated 5-year depreciation schedule. Installing an $85,300 DynGlobal solar energy system could qualify for over $61,000 in first year tax credits and incentives, with a projected return on investment within 6-7 months based on fuel cost savings of $35,VGBC Online Series, Module 5: C叩c ti棚u ch鱈 v畛 Nng l動畛ng trong LOTUS NC v3
VGBC Online Series, Module 5: C叩c ti棚u ch鱈 v畛 Nng l動畛ng trong LOTUS NC v3Vietnam Green Building Council
油
This document provides information about various credits in the LOTUS New Construction energy category. It discusses prerequisites and credits related to minimum energy efficiency, passive design, total building energy use, building envelope, building cooling, artificial lighting, energy monitoring and management, and lifts. For each credit, it provides requirements, calculation methods, compliance options, and examples of projects that have earned the credit. The document aims to help project teams understand the goals of each credit and identify strategies to incorporate energy efficient design features for certification under LOTUS New Construction.New Oorja Presentation
New Oorja Presentationleerts
油
The document discusses methanol fuel cells as an alternative to hydrogen fuel cells for powering forklifts. It provides details on the OorjaPacTM methanol fuel cell system, including its advantages over hydrogen such as lower costs, faster refueling times, and less expensive infrastructure. Customer examples are given that have realized savings and productivity increases through implementing methanol fuel cells.Low-CapEx approach to synthetic transport fuels from biomass From laborator...
Low-CapEx approach to synthetic transport fuels from biomass From laborator...Ilkka Hannula
油
The ambitious targets of the Paris Agreement cannot be met without significant decarbonisation of the transport sector. In Europe, the revised version of the Renewable Energy Directive (REDII) will enter into force by the end of 2019 and will govern European biofuel policies during the next decade. The directive will gradually phase out unsustainable palm oil derived biodiesel, while simultaneously creating European wide demand for low ILUC risk biofuels. Minimum target for low ILUC risk biofuels will be 3.6% by 2030.
In the attempt to accelerate the market introduction of low ILUC risk biofuels, VTT has developed a Low-CapEx concept for biomass-to-liquids (BTL) that can be realised at an intermediate scale of 100-150 MW biomass input (corresponding to 30-50 ktoe annual production of transportation fuels) with an estimated investment cost for a first-of-a-kind plant of around 200 - 300 M. The proposed concept is suitable for non-edible lignocellulosic feedstocks and features an atmospheric steam-blown dual fluidised-bed gasifier combined with a simplified hot-gas clean-up train and a small-scale
Fischer-Tropsch (FT) synthesis.
The pilot-scale development work was started in a national research project BTL2030 during 2016-2018, and is currently being continued in a H2020 project COMSYN. Based on Aspen Plus simulations, the overall efficiency (to both FT fuels and saleable heat) of the process is 79 87 % (LHV). Based on a prospective economic analysis, 1100 1300 /tonne production cost is expected for a first-of-a-kind commercial plant, depending on the price of feedstock. However, significant cost reduction potential exists for subsequent plants through learning-by-doing.
We present main results from our R&D work to date, together with a roadmap on how low ILUC risk biofuels could be deployed during next decade in Europe to meet the targets set in REDII.Offshore wind innovation for cost reduction Wind Europe Summit 2016 Freeman/KIC
Offshore wind innovation for cost reduction Wind Europe Summit 2016 Freeman/KICBVG Associates
油
Presentation by Kate Freeman and KIC InnoEnergy given at the WindEerope Summit in Hamburg, September 2016 on the role innovation has in cost reductionOffshore wind innovation for cost reduction
Offshore wind innovation for cost reductionKate Freeman
油
This document discusses innovation in offshore wind power to reduce costs by 2030. It analyzes the impact of innovations on levelized cost of energy (LCOE) through both technical and commercial perspectives. Key innovations include increased turbine size, more efficient drive trains and components, improved blade aerodynamics and manufacturing, optimized plant development and array layout, advanced support structure design and installation, and condition-based maintenance. Adopting these innovations could reduce LCOE by over 40% compared to current offshore wind farms with 4MW turbines.Advit Foundation - Energy Efficiency
Advit Foundation - Energy EfficiencyAdvit Foundaion
油
The document discusses strategies for mainstreaming energy efficiency and reducing carbon emissions in the Indian apparel industry. It provides an overview of baseline energy consumption and carbon emissions for a typical apparel manufacturing unit. Common energy efficiency measures are identified that could save on average 4.6 lakh units of electricity annually for each unit, reducing costs by 19 lakhs rupees annually after investing 40 lakhs rupees. Implementing energy efficiency and using an ESCO model could reduce carbon emissions from each unit by around 105 tonnes or 7% of current emissions annually. Monitoring and verification plans are needed to track performance and ensure savings.Bringing Energy Cost Control Back to the User
Bringing Energy Cost Control Back to the UserEMEX
油
This document discusses combined heat and power (CHP) and how it can benefit businesses. It begins with an overview of CHP, explaining that it is a form of on-site power generation that provides electricity cost savings while also producing heat for a business. It then provides examples of E.ON implementing CHP solutions for various customers in different industries, including manufacturing, food and beverage, and healthcare. The solutions have resulted in reductions in energy costs and carbon emissions for the customers. CN300: A 300 kWe Turbogenerator for Heat to Power Applications; Generate Ren...
CN300: A 300 kWe Turbogenerator for Heat to Power Applications; Generate Ren...Keith D. Patch
油
Global Cleantech Meetup 2013
Tuesday, November 12, 2013
Boston, MA
Organic Rankine Cycle (ORC) Heat-to-Power Systems are Ideally Suited for Heat to Power Conversion of Natural Heat Sources (Biomass, Geothermal, etc.) or Waste Heat Recovery to Renewable ElectricityVGBC Online Series, Module 5: C叩c ti棚u ch鱈 v畛 Nng l動畛ng trong LOTUS NC v3
VGBC Online Series, Module 5: C叩c ti棚u ch鱈 v畛 Nng l動畛ng trong LOTUS NC v3Vietnam Green Building Council
油
Recently uploaded (20)
IPC-9716_2024 Requirements for Automated Optical Inspection (AOI) Process Con...
IPC-9716_2024 Requirements for Automated Optical Inspection (AOI) Process Con...ssuserd9338b
油
IPC-9716_2024 Requirements for Automated Optical Inspection (AOI) Process Control for Printed Board Assemblies.pdf
How to Make an RFID Door Lock System using Arduino
How to Make an RFID Door Lock System using ArduinoCircuitDigest
油
Learn how to build an RFID-based door lock system using Arduino to enhance security with contactless access control.
Multi objective genetic approach with Ranking
Multi objective genetic approach with Rankingnamisha18
油
Multi objective genetic approach with Ranking 
15. Smart Cities Big Data, Civic Hackers, and the Quest for a New Utopia.pdf
15. Smart Cities Big Data, Civic Hackers, and the Quest for a New Utopia.pdfNgocThang9
油
Smart Cities Big Data, Civic Hackers, and the Quest for a New Utopia
Lecture -3 Cold water supply system.pptx
Lecture -3 Cold water supply system.pptxrabiaatif2
油
The presentation on Cold Water Supply explored the fundamental principles of water distribution in buildings. It covered sources of cold water, including municipal supply, wells, and rainwater harvesting. Key components such as storage tanks, pipes, valves, and pumps were discussed for efficient water delivery. Various distribution systems, including direct and indirect supply methods, were analyzed for residential and commercial applications. The presentation emphasized water quality, pressure regulation, and contamination prevention. Common issues like pipe corrosion, leaks, and pressure drops were addressed along with maintenance strategies. Diagrams and case studies illustrated system layouts and best practices for optimal performance.
Mathematics behind machine learning INT255 INT255__Unit 3__PPT-1.pptx
Mathematics behind machine learning INT255 INT255__Unit 3__PPT-1.pptxppkmurthy2006
油
Mathematics behind machine learning INT255 Water Industry Process Automation & Control Monthly - March 2025.pdf
Water Industry Process Automation & Control Monthly - March 2025.pdfWater Industry Process Automation & Control
油
Welcome to the March 2025 issue of WIPAC Monthly the magazine brought to you by the LinkedIn Group WIPAC Monthly.
In this month's edition, on top of the month's news from the water industry we cover subjects from the intelligent use of wastewater networks, the use of machine learning in water quality as well as how, we as an industry, need to develop the skills base in developing areas such as Machine Learning and Artificial Intelligence.
Enjoy the latest editionSoil Properties and Methods of Determination
Soil Properties and Methods of DeterminationRajani Vyawahare
油
This PPT covers the index and engineering properties of soil. It includes details on index properties, along with their methods of determination. Various important terms related to soil behavior are explained in detail. The presentation also outlines the experimental procedures for determining soil properties such as water content, specific gravity, plastic limit, and liquid limit, along with the necessary calculations and graph plotting. Additionally, it provides insights to understand the importance of these properties in geotechnical engineering applications.
The Golden Gate Bridge a structural marvel inspired by mother nature.pptx
The Golden Gate Bridge a structural marvel inspired by mother nature.pptxAkankshaRawat75
油
The Golden Gate Bridge is a 6 lane suspension bridge spans the Golden Gate Strait, connecting the city of San Francisco to Marin County, California.
It provides a vital transportation link between the Pacific Ocean and the San Francisco Bay.
Water Industry Process Automation & Control Monthly - March 2025.pdf
Water Industry Process Automation & Control Monthly - March 2025.pdfWater Industry Process Automation & Control
油