狠狠撸

FORCE Certification A/S ? Park Alle 345 2605 Br?ndby Tel+45 43 25 01 77 Fax +45 43 25 00 10 info@forcecertification.com www.forcecertification.com
certification.madebydelta.com/weighing
EU Type Examination Certificate
No. 0200-MID-05859
ZM505 / ZM510 / ZM605 / ZM615 Series
AUTOMATIC GRAVIMETRIC FILLING INSTRUMENT
Issued by FORCE Certification
EU - Notified Body No. 0200
In accordance with the requirements in Directive 2014/32/EU of the European Parliament and
Council.
Issued to Avery Weigh-Tronix
Foundry Lane
Smethwick
West Midlands B66 2LP
UNITED KINGDOM
In respect of An automatic gravimetric filling instrument designated ZM505 / ZM510 / ZM605 /
ZM615 Series with variants of modules of load receptors, load cells and peripheral
equipment.
Reference class: Ref (x) = 0.05 (ZM505, ZM510, ZM605, ZM615 Standard build and
when fitted with 10V EXC load celloption card(s))
Ref (x) = 0.1 (5V EXC load cell option card)
Maximum capacity, Maxi= ni× ei
Verification scale interval: e ≥ 0.5 g
Number of verification scale intervals: ni ≤ 10000 (ZM505, ZM510, ZM605, ZM615
standard indicator and 10VEXC load
cell option card)
ni ≤ 6000 (5VEXC load cell option card)
(however, dependent on environment and the composition of the modules)
Variants of modules and conditions for the composition of the modules are set out in
the annex.
The conformity with the essential requirements in Annex 1 and the specific requirements in Annex
VIII (MI-006), chapter I & II of the Directive 2014/32/EU is met by the application of OIML
R61:2004, OIML D11:2013 and WELMEC Guide 7.2:2015.
The principal characteristics and approval conditions are set out in the descriptive
annex to this certificate.
The annex comprises 9 pages.
Issued on 2019-03-22
Valid until 2029-03-22
FORCE Certification references:
Task no.: 119-23235.90.20 and ID no.: 0200-MID-05859 Signatory: J. Hovg?rd Jensen
Jens Hovg?rd Jensen
2019-03-22
Digitally signed by Jens Hovg?rd Jensen
jhje@force.dk
Certification Manager

0200-MID-05859
FORCE Certification A/S ? Park Alle 345 2605 Br?ndby Tel+45 43 25 01 77 Fax +45 43 25 00 10 info@forcecertification.com www.forcecertification.com/
Annex page 1 of 9
Descriptive annex
Contents Page
1. Introduction 2
2. Description of the construction and function 2
2.1 Mechanical 2
2.2 ZM505 / ZM510 / ZM605 / ZM615 Weighing controller 2
2.3 Operation 3
2.4 Software 3
3. Technical data 3
4. Interfaces and peripheral equipment 3
4.1 Interfaces 3
4.2 Peripheral devices 4
5. Approval conditions 4
5.1 Compatibility of modules 4
5.2 Installation 4
5.3 Zero-setting 4
6. Special conditions for verification 4
7. Securing and location of seals and verification marks 4
7.1 Securing and sealing 4
8. Location of CE mark of conformity and inscriptions 5
8.1 Scale 5
9. Pictures 6

0200-MID-05859
Annex page 2 of 9
1. Introduction
This pattern of an automatic gravimetric filling instrument for dispensing predetermined loads of pow-
dered, granular or liquid materials consists of a feeding device, a weighing unit, and a ZM505 /
ZM510 / ZM605 / ZM615 weighing controller (Figures 1-8).
2. Description of the construction and function
2.1 Mechanical
The instrument comprises material handling facilities (feeding device and weighing unit) which shall
enable it to respect the MPEs during normal operation.
2.1.1 Material feeding device
The feeding device may be any one of the following:
- Gravity feeder
- Gravity feeder with agitator
- Single screw or double screw feeder
- Belt feeder
- Vibratory feeder
2.1.2 Weighing unit
The weighing unit is either a load receptor incorporating a weigh hopper and associated discharge de-
vice for weighing of target weights in the weigh hopper (net weighing), or a load receptor without a
discharge device for weighing directly into containers (gross weighing).
2.1.3 Load cell
Any analogue load cell(s) may be used for instruments under this certificate of type examination pro-
vided the following conditions are met:
1) There is a respective OIML Certificate of Conformity (R60) or a Part / Evaluation / Test
Certificate (EN 45501) issued for the load cell by a Notified Body responsible for type ex-
amination under Directive 2014/31/EU.
2) The certificate contains the load cell types and the necessary load cell data required for the
manufacturer’s declaration of compatibility of modules (WELMEC 2:2015), and any partic-
ular installation requirements). A load cell marked NH is allowed only if humidity testing to
EN 45501 has been conducted on this load cell.
3) The compatibility of load cells and indicator is established by the manufacturer by means of
the compatibility of modules form, contained in the above WELMEC 2 document, or the
like, at the time of EC verification or declaration of EC conformity of type.
4) The load transmission must conform to one of the examples shown in the WELMEC 2.4
Guide for load cells.
2.2 ZM505 / ZM510 / ZM605 / ZM615 Weighing controller
The Avery Weigh-Tronix ZM505 / ZM510 / ZM605 / ZM615 weighing controller is fully described in
Evaluation Certificate GB-1577.

0200-MID-05859
Annex page 3 of 9
2.3 Operation
The operator enters or selects the predetermined (target) weight and other operational inputs via the
keys on the front of the controller. The controller operates the filling instrument in response to signals
from the load cell(s) and plant sensors. The operation is fully described in Evaluation Certificate 0200-
WL-05860
2.4 Software
The software and the version of it is fully described in Evaluation Certificate 0200-WL-05860.
3. Technical data
The technical data for the ZM505 / ZM510 / ZM605 / ZM615 weighing controller is as described in
Evaluation Certificate 0200-WL-05860.
4. Interfaces and peripheral equipment
4.1 Interfaces
The instrument may have the following interface types (fully described in Evaluation Certificate 0200-
WL-05860):
- Load cell 4-wire or 6-wire shielded connection
- Logic level inputs
- Open collector outputs
- Analogue outputs
- Current Loop
- RS232/422/485
- 10/100 Ethernet
- USB Host
- Wireless LAN 802.11b/g
- USB Device
- Bluetooth
- DeviceNet
- Profibus
- Power over Ethernet
- DC inputs
- DC outputs
- AC inputs
- AC outputs
- GSE & 1310 legacy interfaces
- Programmable Digital I/O interfaces

0200-MID-05859
Annex page 4 of 9
4.2 Peripheral devices
The instrument may be connected to any peripheral device that has been issued with a Part Certificate
or Evaluation Certificate issued by a Notified Body responsible for Module B under Directive
2014/32/EU and bears the CE marking of conformity to the relevant directives; or
A peripheral device without a Part or Evaluation certificate may be connected under the following
conditions:
- it bears the CE marking for conformity to the EMC Directive;
- it is not capable of transmitting any data or instruction into the weighing instrument, other
than to release a printout, checking for correct data transmission or validation;
- it prints weighing results and other data as received from the weighing instrument without any
modification or further processing; and
- it complies with the applicable requirements of Paragraph 8.1 of Annex I.
5. Approval conditions
5.1 Compatibility of modules
The instrument shall fulfil composition of modules according to EN 45501:2015 annex F.
5.2 Installation
The instrument shall be permanently installed or shall be provided with a level indicator.
5.3 Zero-setting
The ZM505 and ZM510 instruments (including 10V EXC load cell option card) shall be set to zero at
least every 16 min, while the ZM505 and ZM510 instruments if fitted with a 5V EXC load cell option
card shall be set to zero at least every 15 min, via semi-automatic zero-setting, zero-tracking or tare
devices.
The ZM605 and ZM615 instruments (including 10V EXC load cell option card) shall be set to zero at
least every 2 hours 30 min, while the ZM605 and ZM615 instruments if fitted with a 5V EXC load cell
option card shall be set to zero at least every 15 min, via semi-automatic zero-setting, zero-tracking or
tare devices.
6. Special conditions for verification
The environmental conditions should be taken into consideration by the composition of modules for a
complete weighing instrument, for example instruments with load receptors placed outdoors and hav-
ing no special protection against the weather.
The composition of modules shall agree with section 5.1.
7. Securing and location of seals and verification marks
7.1 Securing and sealing
Seals shall bear the verification mark of a notified body or alternative mark of the manufacturer or his
representative according to ANNEX II, module F or D of Directive 2014/32/EU.
The inscription plate is located visible on the indicating device and is secured, either by sealing or by
being of a form such that it is destroyed when removed.

0200-MID-05859
Annex page 5 of 9
Components that may not be dismantled or adjusted by the user (jumper on main board when applica-
ble, electronics, load cell connection) must be secured. Common serial numbers, a wire and seal solu-
tion or a tamper-evident sticker (bearing a securing mark) may be used.
When software sealing is used, the CONFIG and CAL counters’ values shall be written on a tamper-
evident label on or near the rating plate.
8. Location of CE mark of conformity and inscriptions
8.1 Scale
8.1.1 CE mark
CE mark and supplementary metrological marking shall be applied to the instrument according to arti-
cle 20 of Directive 2014/32/EU.
8.1.2 Inscriptions
Max, Min, and d shall be located near the display.
On the inscription plate of the instrument:
? Manufacturer’s name and/or trademark
? Postal address of manufacturer
? Type designation
? Serial number
? Product(s) designation
? Reference class Ref(x)
? Accuracy class X(x)
? Max, Min, d
? Temperature range: -10 / +40 °C (optional)
? Electromagnetic class: E2
? Humidity: Non-condensing
? EU type examination certificate number
? Supply voltage
? Pneumatic/hydraulic pressure (if applicable)
? Maximum subtractive tare (if ≠ -Max)
? Information in respect of the conditions of use (if applicable)
? Information whether or not additional devices providing metrological results comply with
the provisions of Directive 2014/32/EU on legal metrological control (if applicable)
The markings and inscriptions shall fulfil the requirements of Article 8, Article 21, Article 22 and
Point 9 of Annex I of Directive 2014/32/EU.

0200-MID-05859
Annex page 6 of 9
9. Pictures
Figure 1 ZM505-SD3 weighing controller
Figure 2 ZM505-SP3 weighing controller

0200-MID-05859
Annex page 7 of 9

0200-MID-05859
Annex page 8 of 9

0200-MID-05859
Annex page 9 of 9

狠狠撸

midmid_0200_mid_05859_averyweightronix.pdf

Recommended

More Related Content

Similar to midmid_0200_mid_05859_averyweightronix.pdf (20)

Recently uploaded (18)

midmid_0200_mid_05859_averyweightronix.pdf