More Related Content
What's hot (12)
Viewers also liked (7)
Similar to CERTIFICATE-E-MARK-E11-10R-048662 (20)
CERTIFICATE-E-MARK-E11-10R-048662
- 1. MSQ308007 An executive agency of the Department for Transport June 2012 Revision 0 1 THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY COMMUNICATION CONCERNING THE APPROVAL GRANTED (1) / APPROVAL EXTENDED (1) / APPROVAL REFUSED (1) / APPROVAL WITHDRAWN (1) / PRODUCTION DEFINITIVELY DISCONTINUED (1) OF A TYPE OF ELECTRICAL/ ELECTRONIC SUB-ASSEMBLY (1) WITH REGARD TO REGULATION NO. 10.04 Approval No: 10R-048662 Extension No: Not applicable 1. Make (trade name of manufacturer): Ultimate Power速, Lda. 2. Type and general commercial description(s): UCCE V2.0 Ultimate Cell UCTE V2.0 Ultimate Cell UCBE V2.0 Ultimate Cell 3. Means of identification of type, if marked on the vehicle/component/ separate technical unit: (1) 3.1. Location of that marking: See manufacturers documentation 4. Category of vehicle: Not applicable 5. Name and address of manufacturer: Ultimate Power速, Lda Estrada de Pa巽os de Arcos 66捉 2735-336 Cac辿m Portugal 6. In the case of components and separate technical units, location and method of affixing of the ECE approval mark: Engraved in the plastic injection mold components UK A pproval Auth ority 31-Oct-14
- 2. E11 10R-048662 MSQ308007 An executive agency of the Department for Transport June 2012 Revision 0 2 7. Address(es) of assembly plant(s): As paragraph 5 8. Additional information (where applicable): See appendix 9. Technical Service responsible for carrying out the tests: Vehicle Certification Agency 10. Date of test report: 07 October 2014 11. No. of test report: MSQ308007 12. Any remarks: Approval to Supplement 2 See Appendix 13. Place: BRISTOL 14. Date: 31 OCTOBER 2014 15. Signature: A. W. STENNING Head of Technical and Quality Support Group 16. The index to the information package lodged with the Approval Authority, which may be obtained on request, is attached. 17. Reasons for extension: Not applicable (1) Strike out what does not apply. UK A pproval Auth ority 31-Oct-14
- 3. E11 10R-048662 MSQ308007 An executive agency of the Department for Transport June 2012 Revision 0 3 Appendix to type-approval communication form No. 10R-048662 concerning the type-approval of an electrical/electronic sub-assembly under Regulation No. 10.04 1. Additional information:. 1.1. Electrical system rated voltage: 13.5V. pos/neg ground (1) 1.2. This ESA can be used on any vehicle type with the following restrictions: Not applicable 1.2.1. Installation conditions, if any: 1.3. This ESA can be used only on the following vehicle types: M, N 1.3.1. Installation conditions, if any: See manufacturers documents 1.4. The specific test method(s) used and the frequency ranges covered to determine immunity were: (Please specify precise method used from Annex 9): BCI: Actual frequency range used: 20 220MHz Free field: Actual frequency range used: 200 2000MHz 1.5. Laboratory accredited to ISO 17025 and recognized by the Approval Authority responsible for carrying out the tests: Not applicable 2. Remarks: None (1) Strike out what does not apply. UK A pproval Auth ority 31-Oct-14
- 4. Date: 29/09/2014 Page 1/3 VCA Job Number: MSQ308007 Ultimate Power R10.04 Manufacturer: ULTIMATE POWER速 , Lda Adress: Estrada de Pa巽o de Arcos 66捉 2735 336 Cac辿m Portugal Mail: geral@ultimatepower.pt Site: www.ultimatepower.pt UK A pproval Auth ority 31-Oct-14
- 5. Date: 29/09/2014 Page 2/3 ANNEX 2B 1. Make (trade name of manufacturer): - Ultimate Power 速 , Lda. 2. Type: - Ultimate Cell 速 , is an optimization device for internal combustion engines, which reduces both fuel consumption and exhaust emissions. UCCE V2.0 Ultimate Cell UCTE V2.0 Ultimate Cell UCBE V2.0 Ultimate Cell 3. Means of identification of type, if marked on the component/separate technical unit ( 1 ): 3.1. Location of that marking: - All equipments are properly identified with a sequential code traceability placed on the device and on the package. At the top of the equipment, is engraved on the injection mold the CE marking. After the approval of VCA, it will be engraved on the top cover the E-mark. 4. Name and address of manufacturer: - Ultimate Power 速 , Lda Address- Estrada de Pa巽os de Arcos 66捉, 2735-336 Cac辿m, Portugal Name and address of authorised representative, if any: - Qualiseg, Rua da Bela Vista n尊 110 2捉, 2825-004 Caparica, Portugal 5. In the case of components and separate technical units, location and method of affixing of the approval mark: - The approval mark shall be engraved in the plastic injection mold components and in the final product packaging. 6. Address(es) of assembly plant(s): - Ultimate Power速, Lda Address: Estrada de Pa巽os de Arcos, 66 A 2735-336 Cac辿m Portugal UK A pproval Auth ority 31-Oct-14
- 6. Date: 29/09/2014 Page 3/3 7. This ESA shall be approved as a STU 8. Any restrictions of use and conditions for fitting: The equipment maybe use in any internal combustion engines, being effective on diesel, petrol and LPG engines. The installation of the ULTIMATE CELL must be done only by certified installers approved by Ultimate Power速 , Lda. The device should be as far as possible from the exhaust manifold, the turbo and from all exposed engine moving parts also it should be placed in an upright position (+/-15 deg), with the outlet cover on the top. 9. Electrical system rated voltage: 13,5 V, positive ( 2 ) ground. ....................................................................................... Appendix 1: 5010 - UCCE Assembled 5011 - UCBE Assembled 5010 - UCTE Assembled Diagrama blocos PCB Bill of Material Appendix 2: Tests Ficha de Dados de Seguran巽a Electrolito UCCE Ficha de Dados de Seguran巽a Electrolito UCTE_UCBE UK A pproval Auth ority 31-Oct-14