Water bath, bacteriological
Download as doc, pdf0 likes476 views
This document describes the specifications of a water bath used for incubating culture tubes in coliform analysis. The water bath has an inner size of approximately 0.4 x 0.3 x 0.15 meters, is made of stainless steel inside and stove enameled outside, and can maintain temperatures from ambient to 50°C with an accuracy of ±0.1°C. It has a double wall for insulation, a dome lid to hold test tubes vertically, and displays the internal water temperature.
1 of 1
Download to read offline
Ad
Recommended
Water bath, general purpose
Water bath, general purposehydrologyproject0A general purpose water bath has an inner size of approximately 0.4 x 0.3 x 0.1 meters, is made of stainless steel inside and stove enameled outside, and can maintain temperatures from ambient to 100°C with an accuracy of ±2°C. It has a stainless steel cover with 12 holes and features a drain cock or plug, double-walled insulation, and a pilot lamp to indicate thermostat operation.
Water geyser (heater)
Water geyser (heater)hydrologyproject0This document specifies a water geyser (heater) that has a 120 liter capacity, heats water to 90°C with thermostatic control, and requires a 220 VAC ±25%, 47 to 53 Hz power supply for operation in a laboratory setting.
Water purifier, double distillation unit
Water purifier, double distillation unithydrologyproject0This document provides specifications for a double distillation water purification unit. It distills water to a conductivity of 1.0 μS/cm or less at 25°C for generating reagent-grade water. The unit is made of quartz glass with a 1.5 liter/hour capacity. It runs on 220V power and includes a metallic stand, ring clamp, and operation manual. Safety features include over-heating protection and indicators.
Water purifier, distillation unit (automatic)
Water purifier, distillation unit (automatic)hydrologyproject0This document provides specifications for an automatic water distillation unit. The unit distills water to generate reagent water type III with a maximum conductivity of 0.01 mS/cm at 25°C for use in washing and quantitative analysis. It has a stainless steel construction, 1.5 liter per hour capacity, operates on 220VAC power, and has automatic shutoff when water levels are low.
Oven, general purpose
Oven, general purposehydrologyproject0This document provides specifications for a general purpose oven used for laboratory drying, heating, and evaporating of glassware, samples, and chemicals. The oven has a stainless steel interior with enameled exterior, a temperature range of ambient to 250°C controlled via a thermostat, built-in digital thermometer, timer of at least 2 hours adjustable in 15 minute increments, and requires a 220V power supply. Key features include double wall insulation, pilot light, adjustable shelves, ventilation, sturdy hinges and a roller latch door.
Bod or-low-temp-incubator
Bod or-low-temp-incubatorAcmas Technologies Pvt.LtdThis document describes a low temperature incubator model ACM-I03429B made by Technocracy Pvt. Ltd. for testing biochemical oxygen demand of wastewater. The incubator has a temperature range of 2°C to 90°C and is used to determine levels of organic matter and nitrogen in wastewater samples. It has features like PID temperature control, LED display, forced air circulation and can be used for applications like BOD determinations, enzyme assays, and bacterial culturing.
Incubator, bod
Incubator, bodhydrologyproject0This document provides specifications for a biochemical oxygen demand incubator. The incubator has an inner chamber measuring approximately 0.5 x 0.5 x 0.8 meters made of stainless steel. It has a temperature range of 5 to 50 degrees Celsius controlled by a thermostat with an accuracy of ±0.5 degrees. Additional features include shelves, motorized air circulation, an insulated wall, and a glass door to monitor samples without temperature disturbance.
BOD Incubator by ACMAS Technologies Pvt Ltd.
BOD Incubator by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.Technocracy Pvt. Ltd. manufactures versatile and energy-efficient BOD incubators, utilizing double-walled convection heating and stainless steel construction for laboratories in India since 1990. Their incubators support biochemical oxygen demand tests, featuring customized models, temperature control from 5°C to 60°C, and data logging capabilities for research applications. The units are designed with ergonomic features, safety mechanisms, and options for customization to meet diverse scientific needs across various regions.
Fume cupboard
Fume cupboardhydrologyproject0The document specifies the requirements and features for a fume cupboard version 2, including an optimal air flow pattern, a water tap and sink, double socket electricity, fire proof inner surface, acid/alkali proof tiles, exhaust fan, ducting, double skin fabrication, and glass sliding front sash with counter weight to ventilate hazardous fumes safely during analysis.
Incubator, bacteriological
Incubator, bacteriologicalhydrologyproject0This document specifies an incubator for bacteriological analysis with a stainless steel interior chamber, temperature range of 35-60 degrees Celsius controlled within 1 degree accuracy, digital display, 3 shelves, glass door, and includes a thermometer for measuring the interior temperature.
Types of BOD Incubator by ACMAS Technologies Pvt Ltd.
Types of BOD Incubator by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.The document provides detailed information about the B.O.D (Biochemical Oxygen Demand) incubators produced by ACMAS Technocracy Pvt. Ltd., including their construction, applications, and technical specifications. These incubators are designed for various laboratory uses such as wastewater analysis, plant cell growth, and fermentation studies, featuring programmable temperature controls and data logging capabilities. Additionally, it highlights the insulation, refrigeration system, and optional features available for these incubators.
Hot plate
Hot platehydrologyproject0This document provides specifications for a laboratory hot plate. The hot plate is approximately 0.3 by 0.45 meters in size, can heat from ambient temperature to 300 degrees Celsius, and has a thermostatically controlled temperature range. It has a 2000 Watt spiral heater made of best quality materials embedded in a cast iron top plate attached to a hot enameled mild steel body, and runs on 220 VAC power supply between 47-53 Hz.
Refrigerator
Refrigeratorhydrologyproject0This document provides specifications for a laboratory refrigerator. It is a vertical double door refrigerator with a 280 liter capacity. It runs on 140-280 VAC at 47-53 Hz and maintains a continuous temperature of 4°C. Key features include a built-in voltage stabilizer, two doors and three trays, self-draining defrosting, PUF insulation, and a locking system.
Electric stove oven
Electric stove ovenhydrologyproject0The document specifies requirements for an electric stove that will be used to dry sediment samples. The stove must be safe to operate and prevent spilled water from causing corrosion or reaching electric components. It must also comply with industry standard IS 2994-1992. Key specifications include dimensions of approximately 0.4 x 0.3 x 0.3 meters, a temperature range of 50-150°C controlled within 1°C, an external thermometer, two adjustable trays, and a 220V power supply.
Deep freezer
Deep freezerhydrologywebsite1The document describes a deep freezer used for preparing and storing ice and water quality samples. It has a 300-liter capacity, temperature range of -20°C to +20°C, automatic operation, and is made of stainless steel inside and hot enameled outside. Additional features include a built-in voltage stabilizer, two doors and three trays, fully automatic and frost-free operation, self-draining defrosting, PUF insulation, and a low noise compressor.
CO2 Incubator Economy - SCO6WE, SCO12WE
CO2 Incubator Economy - SCO6WE, SCO12WESheldon Manufacturing, Inc.This document summarizes the features of a CO2 incubator model. It has a PID microprocessor controller, heated outer door, tempered glass inner door, and maintains temperature uniformity while minimizing condensation. It has alarms for temperature and CO2 levels out of tolerance. It uses infrared sensors for fast CO2 recovery and stability. Extensive copper is used throughout to control contamination, and it maintains temperature, CO2 levels, and humidity to replicate mammalian environments for tissue and cell culture. It comes with a 5-year parts warranty and lifetime warranty on the water jacket chamber.
Temperature measurement and control in bioreactor
Temperature measurement and control in bioreactorAATHILAKSHMI URUMANATHANThe document discusses the importance of temperature measurement and control in bioreactors, highlighting various types of thermometers such as thermocouples, thermistors, and resistance temperature detectors (RTDs). It outlines their functionality, advantages, and limitations, particularly emphasizing how precise temperature control is vital for enzyme activity and overall reaction efficiency. The text also covers common methods used for temperature control in both small and large fermenters.
Genie 745 production gas sampling system datasheet
Genie 745 production gas sampling system datasheeta1-cbissThe Production Gas Sampling System (PGSS) provides a liquid-free, low pressure sample from natural gas streams for process control analysis. It extracts the sample using a direct-drive probe, removes liquids using a coalescing filter and membrane separator, and reduces pressure using a heated regulator without Joule-Thomson cooling effects. Optional heat tubing allows compatibility with low and high dew points. The PGSS mounts directly onto pipelines for accurate sampling close to wellheads.
Combustion Analyzer to Add Extra Layer of Safety to Burner Management System
Combustion Analyzer to Add Extra Layer of Safety to Burner Management SystemBelilove Company-EngineersThe WDG-V combustion analyzer enhances burner management systems by measuring excess oxygen, combustibles, and methane to ensure safe operation and maintain efficiency. Designed with built-in redundancy, it supports predictive maintenance and complies with safety standards like SIL 2 and IEC 61508/61511. Its compact, user-friendly design facilitates operational reliability and allows for easy calibration and diagnostics.
Economical Sodium Ion Concentration Meter by ACMAS Technologies Pvt Ltd.
Economical Sodium Ion Concentration Meter by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.The document details the features and specifications of the ACM-DWS-51 economical sodium ion concentration meter, which utilizes advanced embedded MCU technology for accuracy in sodium concentration measurement. It includes a bright LED display, automatic temperature compensation, and is designed for ease of use through one-button operation and two-point calibration. Key technical specifications cover measurement range, precision, and operational conditions, and the product is compliant with various quality and environmental standards.
Laboratory heating and cooling instruments Manufacturer From India
Laboratory heating and cooling instruments Manufacturer From IndiaMicroteknik - A Symbol of QualityThe document details a comprehensive overview of 'Teknik' products, including various laboratory instruments such as autoclaves, incubators, and water baths, highlighting their construction, specifications, and features. It emphasizes the company's commitment to quality through extensive R&D and gratitude towards clients for their support and suggestions. The products are designed with advanced technology, aiming to serve as import substitutes in the market.
Quality Assurance in the Metals Lab
Quality Assurance in the Metals LabRyan BrennanThis document discusses factors for achieving high quality in a metals laboratory. It focuses on controlling sample uptake rate using a real-time flow monitor, controlling spray chamber temperature which improves accuracy and reproducibility for various elements, and controlling interferences using an internal standardization kit. Maintaining proper system maintenance and controlling downtime enhances day-to-day reproducibility.
Chronomite Laboratories, Inc.
Chronomite Laboratories, Inc.Morris Group InternationalChronomite specializes in tankless electric water heaters, emphasizing efficiency, longevity, and easy installation. These heaters provide unlimited hot water with up to 99% energy efficiency, avoiding common code requirements associated with traditional tank systems. Their products are microprocessor controlled for precise temperature regulation, safety features, and compatibility with various applications including public lavatories and emergency eyewash stations.
Domestic integrated heat pump blueway
Domestic integrated heat pump bluewayRoger LuoThe document describes the Blueway Integrated Heat Pump Water Heater, designed for kitchen and bathroom applications, using eco-friendly refrigerants to efficiently heat water and reduce electricity consumption by 70-80% compared to conventional heaters. It features a unique design that ensures no contamination risk to potable water, easy installation, and operates quietly. Additionally, the unit incorporates heat recovery technology, utilizing wasted energy from surrounding environments for hot water production.
Cold chamber
Cold chamberGotmenowSoftSolutionIsotech Pvt Ltd's cold chamber is designed for environmental testing, maintaining temperatures between -70°C and +80°C with a high level of precision. It features a stainless steel construction, advanced temperature control systems, and a user-friendly interface for operation and monitoring. The chamber prioritizes safety with multiple protection mechanisms and is suitable for various testing applications.
Arabidopsis chamber
Arabidopsis chamberAcmas Technologies Pvt.LtdThe Arabidopsis Chamber is designed to provide an optimum growth environment for Arabidopsis plants. It controls temperature, humidity, CO2, and lighting levels. The chamber uses an IntellusUltra controller and patented lamp banks that require less energy than typical lamps but still provide maximum light intensity. The chamber allows for simulating different weather and radiation conditions for plant growth experiments.
ENVIORNMENTAL TEST CHAMBERS
ENVIORNMENTAL TEST CHAMBERSacmasindiaThis document describes an environmental test chamber manufactured by Technologies Pvt. Ltd. It summarizes the chamber's features, which include precise control of temperature, humidity, and light parameters for testing various samples. The chamber uses microprocessor-based controllers and is constructed for stability, energy efficiency, and low maintenance. Technologies Pvt. Ltd specializes in customized chambers for research applications across industries like pharmaceuticals and manufacturing.
Drosophila chamber series
Drosophila chamber seriesSheldon Manufacturing, Inc.The Shel Lab has developed a specialized low-temperature incubator for Drosophila that optimizes temperature control to enhance breeding conditions while minimizing ice build-up. Key features include a microprocessor-controlled light for breeding cycles, energy-efficient operation, and a design that minimizes compressor noise and maintenance. The incubator has precise temperature regulation, a 20.3 cu. ft. capacity, and comes with a two-year limited warranty.
Specification purewater
Specification purewaterhydrologyproject0The document summarizes a water purification system that includes a reverse osmosis unit, storage tank, and ultrapure water purification unit. The system uses a microprocessor to control purification from a municipal water supply to produce at least 35 liters/hour of water with a resistivity of 18 megohm cm or higher that is at least 99% free of bacteria, ions, organics, and particles. The system is also capable of continuous monitoring and will automatically shut off if the feed water is inadequate or the storage tank reaches capacity.
Water purifier ion exchange resin column
Water purifier ion exchange resin columnhydrologyproject0The document describes a water purifier using ion exchange resin columns that produces reagent-grade water for trace analysis. It has separate cation and anion exchange columns with a capacity of 25 liters each and can purify water at a rate over 1 liter per minute. Accessories include spare columns, instructions, a cover, and vacuum hose. Key features are an inline conductivity monitor and the ability to regenerate the resin columns.
More Related Content
What's hot (20)
Fume cupboard
Fume cupboardhydrologyproject0The document specifies the requirements and features for a fume cupboard version 2, including an optimal air flow pattern, a water tap and sink, double socket electricity, fire proof inner surface, acid/alkali proof tiles, exhaust fan, ducting, double skin fabrication, and glass sliding front sash with counter weight to ventilate hazardous fumes safely during analysis.
Incubator, bacteriological
Incubator, bacteriologicalhydrologyproject0This document specifies an incubator for bacteriological analysis with a stainless steel interior chamber, temperature range of 35-60 degrees Celsius controlled within 1 degree accuracy, digital display, 3 shelves, glass door, and includes a thermometer for measuring the interior temperature.
Types of BOD Incubator by ACMAS Technologies Pvt Ltd.
Types of BOD Incubator by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.The document provides detailed information about the B.O.D (Biochemical Oxygen Demand) incubators produced by ACMAS Technocracy Pvt. Ltd., including their construction, applications, and technical specifications. These incubators are designed for various laboratory uses such as wastewater analysis, plant cell growth, and fermentation studies, featuring programmable temperature controls and data logging capabilities. Additionally, it highlights the insulation, refrigeration system, and optional features available for these incubators.
Hot plate
Hot platehydrologyproject0This document provides specifications for a laboratory hot plate. The hot plate is approximately 0.3 by 0.45 meters in size, can heat from ambient temperature to 300 degrees Celsius, and has a thermostatically controlled temperature range. It has a 2000 Watt spiral heater made of best quality materials embedded in a cast iron top plate attached to a hot enameled mild steel body, and runs on 220 VAC power supply between 47-53 Hz.
Refrigerator
Refrigeratorhydrologyproject0This document provides specifications for a laboratory refrigerator. It is a vertical double door refrigerator with a 280 liter capacity. It runs on 140-280 VAC at 47-53 Hz and maintains a continuous temperature of 4°C. Key features include a built-in voltage stabilizer, two doors and three trays, self-draining defrosting, PUF insulation, and a locking system.
Electric stove oven
Electric stove ovenhydrologyproject0The document specifies requirements for an electric stove that will be used to dry sediment samples. The stove must be safe to operate and prevent spilled water from causing corrosion or reaching electric components. It must also comply with industry standard IS 2994-1992. Key specifications include dimensions of approximately 0.4 x 0.3 x 0.3 meters, a temperature range of 50-150°C controlled within 1°C, an external thermometer, two adjustable trays, and a 220V power supply.
Deep freezer
Deep freezerhydrologywebsite1The document describes a deep freezer used for preparing and storing ice and water quality samples. It has a 300-liter capacity, temperature range of -20°C to +20°C, automatic operation, and is made of stainless steel inside and hot enameled outside. Additional features include a built-in voltage stabilizer, two doors and three trays, fully automatic and frost-free operation, self-draining defrosting, PUF insulation, and a low noise compressor.
CO2 Incubator Economy - SCO6WE, SCO12WE
CO2 Incubator Economy - SCO6WE, SCO12WESheldon Manufacturing, Inc.This document summarizes the features of a CO2 incubator model. It has a PID microprocessor controller, heated outer door, tempered glass inner door, and maintains temperature uniformity while minimizing condensation. It has alarms for temperature and CO2 levels out of tolerance. It uses infrared sensors for fast CO2 recovery and stability. Extensive copper is used throughout to control contamination, and it maintains temperature, CO2 levels, and humidity to replicate mammalian environments for tissue and cell culture. It comes with a 5-year parts warranty and lifetime warranty on the water jacket chamber.
Temperature measurement and control in bioreactor
Temperature measurement and control in bioreactorAATHILAKSHMI URUMANATHANThe document discusses the importance of temperature measurement and control in bioreactors, highlighting various types of thermometers such as thermocouples, thermistors, and resistance temperature detectors (RTDs). It outlines their functionality, advantages, and limitations, particularly emphasizing how precise temperature control is vital for enzyme activity and overall reaction efficiency. The text also covers common methods used for temperature control in both small and large fermenters.
Genie 745 production gas sampling system datasheet
Genie 745 production gas sampling system datasheeta1-cbissThe Production Gas Sampling System (PGSS) provides a liquid-free, low pressure sample from natural gas streams for process control analysis. It extracts the sample using a direct-drive probe, removes liquids using a coalescing filter and membrane separator, and reduces pressure using a heated regulator without Joule-Thomson cooling effects. Optional heat tubing allows compatibility with low and high dew points. The PGSS mounts directly onto pipelines for accurate sampling close to wellheads.
Combustion Analyzer to Add Extra Layer of Safety to Burner Management System
Combustion Analyzer to Add Extra Layer of Safety to Burner Management SystemBelilove Company-EngineersThe WDG-V combustion analyzer enhances burner management systems by measuring excess oxygen, combustibles, and methane to ensure safe operation and maintain efficiency. Designed with built-in redundancy, it supports predictive maintenance and complies with safety standards like SIL 2 and IEC 61508/61511. Its compact, user-friendly design facilitates operational reliability and allows for easy calibration and diagnostics.
Economical Sodium Ion Concentration Meter by ACMAS Technologies Pvt Ltd.
Economical Sodium Ion Concentration Meter by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.The document details the features and specifications of the ACM-DWS-51 economical sodium ion concentration meter, which utilizes advanced embedded MCU technology for accuracy in sodium concentration measurement. It includes a bright LED display, automatic temperature compensation, and is designed for ease of use through one-button operation and two-point calibration. Key technical specifications cover measurement range, precision, and operational conditions, and the product is compliant with various quality and environmental standards.
Laboratory heating and cooling instruments Manufacturer From India
Laboratory heating and cooling instruments Manufacturer From IndiaMicroteknik - A Symbol of QualityThe document details a comprehensive overview of 'Teknik' products, including various laboratory instruments such as autoclaves, incubators, and water baths, highlighting their construction, specifications, and features. It emphasizes the company's commitment to quality through extensive R&D and gratitude towards clients for their support and suggestions. The products are designed with advanced technology, aiming to serve as import substitutes in the market.
Quality Assurance in the Metals Lab
Quality Assurance in the Metals LabRyan BrennanThis document discusses factors for achieving high quality in a metals laboratory. It focuses on controlling sample uptake rate using a real-time flow monitor, controlling spray chamber temperature which improves accuracy and reproducibility for various elements, and controlling interferences using an internal standardization kit. Maintaining proper system maintenance and controlling downtime enhances day-to-day reproducibility.
Chronomite Laboratories, Inc.
Chronomite Laboratories, Inc.Morris Group InternationalChronomite specializes in tankless electric water heaters, emphasizing efficiency, longevity, and easy installation. These heaters provide unlimited hot water with up to 99% energy efficiency, avoiding common code requirements associated with traditional tank systems. Their products are microprocessor controlled for precise temperature regulation, safety features, and compatibility with various applications including public lavatories and emergency eyewash stations.
Domestic integrated heat pump blueway
Domestic integrated heat pump bluewayRoger LuoThe document describes the Blueway Integrated Heat Pump Water Heater, designed for kitchen and bathroom applications, using eco-friendly refrigerants to efficiently heat water and reduce electricity consumption by 70-80% compared to conventional heaters. It features a unique design that ensures no contamination risk to potable water, easy installation, and operates quietly. Additionally, the unit incorporates heat recovery technology, utilizing wasted energy from surrounding environments for hot water production.
Cold chamber
Cold chamberGotmenowSoftSolutionIsotech Pvt Ltd's cold chamber is designed for environmental testing, maintaining temperatures between -70°C and +80°C with a high level of precision. It features a stainless steel construction, advanced temperature control systems, and a user-friendly interface for operation and monitoring. The chamber prioritizes safety with multiple protection mechanisms and is suitable for various testing applications.
Arabidopsis chamber
Arabidopsis chamberAcmas Technologies Pvt.LtdThe Arabidopsis Chamber is designed to provide an optimum growth environment for Arabidopsis plants. It controls temperature, humidity, CO2, and lighting levels. The chamber uses an IntellusUltra controller and patented lamp banks that require less energy than typical lamps but still provide maximum light intensity. The chamber allows for simulating different weather and radiation conditions for plant growth experiments.
ENVIORNMENTAL TEST CHAMBERS
ENVIORNMENTAL TEST CHAMBERSacmasindiaThis document describes an environmental test chamber manufactured by Technologies Pvt. Ltd. It summarizes the chamber's features, which include precise control of temperature, humidity, and light parameters for testing various samples. The chamber uses microprocessor-based controllers and is constructed for stability, energy efficiency, and low maintenance. Technologies Pvt. Ltd specializes in customized chambers for research applications across industries like pharmaceuticals and manufacturing.
Drosophila chamber series
Drosophila chamber seriesSheldon Manufacturing, Inc.The Shel Lab has developed a specialized low-temperature incubator for Drosophila that optimizes temperature control to enhance breeding conditions while minimizing ice build-up. Key features include a microprocessor-controlled light for breeding cycles, energy-efficient operation, and a design that minimizes compressor noise and maintenance. The incubator has precise temperature regulation, a 20.3 cu. ft. capacity, and comes with a two-year limited warranty.
Types of BOD Incubator by ACMAS Technologies Pvt Ltd.
Types of BOD Incubator by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.
CO2 Incubator Economy - SCO6WE, SCO12WE
CO2 Incubator Economy - SCO6WE, SCO12WESheldon Manufacturing, Inc.
Temperature measurement and control in bioreactor
Temperature measurement and control in bioreactorAATHILAKSHMI URUMANATHAN
Genie 745 production gas sampling system datasheet
Genie 745 production gas sampling system datasheeta1-cbiss
Combustion Analyzer to Add Extra Layer of Safety to Burner Management System
Combustion Analyzer to Add Extra Layer of Safety to Burner Management SystemBelilove Company-Engineers
Economical Sodium Ion Concentration Meter by ACMAS Technologies Pvt Ltd.
Economical Sodium Ion Concentration Meter by ACMAS Technologies Pvt Ltd.Acmas Technologies Pvt. Ltd.
Laboratory heating and cooling instruments Manufacturer From India
Laboratory heating and cooling instruments Manufacturer From IndiaMicroteknik - A Symbol of Quality
More from hydrologyproject0 (20)
Specification purewater
Specification purewaterhydrologyproject0The document summarizes a water purification system that includes a reverse osmosis unit, storage tank, and ultrapure water purification unit. The system uses a microprocessor to control purification from a municipal water supply to produce at least 35 liters/hour of water with a resistivity of 18 megohm cm or higher that is at least 99% free of bacteria, ions, organics, and particles. The system is also capable of continuous monitoring and will automatically shut off if the feed water is inadequate or the storage tank reaches capacity.
Water purifier ion exchange resin column
Water purifier ion exchange resin columnhydrologyproject0The document describes a water purifier using ion exchange resin columns that produces reagent-grade water for trace analysis. It has separate cation and anion exchange columns with a capacity of 25 liters each and can purify water at a rate over 1 liter per minute. Accessories include spare columns, instructions, a cover, and vacuum hose. Key features are an inline conductivity monitor and the ability to regenerate the resin columns.
Wash bottle
Wash bottlehydrologyproject0The document specifies the requirements for a wash bottle used to flush glassware. The wash bottle must be made of polythene, hold 500 ml of liquid, and have a bent nozzle and screw cap. It was last reviewed on October 23, 2007 and is used to wash away any sticking sediment from glassware.
Volumetric flask
Volumetric flaskhydrologyproject0The document specifies volumetric flasks that will be used for sediment analyses in a laboratory. The flasks must comply with IS 915-1975, be made of Corning glass or similar material, and come in sizes of 50, 100, 250, and 500 ml with B class accuracy.
Visual accumulation tube
Visual accumulation tubehydrologyproject0The visual accumulation tube is used to assess particle sizes of sediments. It consists of a vertical transparent settling tube through which sediment samples are passed. Particles settle individually based on terminal velocity related to diameter, and accumulated sediment volume in the tube's narrow end relates to solid weight. It is best for uniform, spherical particles. The analysis involves introducing a small sample and recording accumulated sediment height over time.
Vacuum pump
Vacuum pumphydrologyproject0This document provides specifications for a vacuum pump for general laboratory use. The pump is a single stage pump with a capacity of 50 l/min, capable of reaching a final vacuum of 0.05 mm Hg without ballast or 2 mm Hg with ballast. It has a 200W motor that operates on 220VAC at 47-53 Hz. Accessories include a filter, regulator, gauge, hose, and valve. The pump is designed for noise free operation.
Turbidity meter (nephelometer)
Turbidity meter (nephelometer)hydrologyproject0This document provides specifications for a turbidity meter used to directly measure suspended matter in water samples. The turbidity meter has a range of 0 to 1000 NTU in at least 2 ranges, an accuracy of ±2% full scale deflection, and requires a power supply of 220 VAC ±25%, 47 to 53 Hz. Accessories for the turbidity meter include an ambient light shield, 6 spare tubes, a sensor stand, voltage stabilizer, instruction manual, and dust cover.
Tool kit
Tool kithydrologyproject0This tool kit contains basic tools for minor repairs of electrical laboratory equipment, including a set of screwdrivers, pliers, soldering iron, and multi-meter. The tools come in a lockable storage box for organization and security.
Toc analyser, microprocessor controlled
Toc analyser, microprocessor controlledhydrologyproject0The document specifies the requirements for a microprocessor-controlled TOC analyzer. It must be able to directly measure total carbon, total organic carbon, and purgeable organic carbon in water samples. It uses high temperature catalytic combustion up to 900°C and non-dispersive infrared detection. It must have a measuring range of 1-500 mg/L carbon, precision within 3%, and detection limit of at least 500 ppb carbon. The analyzer and auto-sampler require 240V 50Hz power and it uses nitrogen or high purity air as carrier gases. It includes an auto-sampler, syringes, printer, manuals, spare parts, and application software in English.
Tissue grinder
Tissue grinderhydrologyproject0This document provides specifications for a tissue grinder used to prepare tissue or sediment samples. The grinder must be able to macerate glass fibre filters and is a manual, porcelain device used to homogenize samples for further analysis such as chemical extraction.
Thermometers, set of
Thermometers, set ofhydrologyproject0This document specifies a set of thermometers for laboratory use, including mercury-filled glass thermometers with three temperature ranges (0-80oC, 10-150oC, 20-250oC) and an accuracy of ±0.5oC, along with a storage box for the thermometers.
Test tubes
Test tubeshydrologyproject0This document specifies test tubes for laboratory use in sediment analysis. It outlines that the test tubes should be made of Corning glass or similar material, and lists two standard sizes - 15 x 125 mm and 25 x 200 mm in diameter and height. The test tubes are intended for general use in analyzing sediments in the laboratory.
Test sieves with shaker
Test sieves with shakerhydrologyproject0The document specifies requirements for test sieves with a shaker. It requires stainless steel sieves that are 200mm in diameter, 50mm in height, and have nominal aperture sizes between 63-250 micrometers. It also requires a shaker capable of holding at least 5 sieves that runs on 220V power. Accessories include a sieve brush and wash bottle. Some sieves can be used manually without the shaker.
Stirrer, magnetic (with hot plate)
Stirrer, magnetic (with hot plate)hydrologyproject0This document provides specifications for a magnetic stirrer with a hot plate. It can rotate between 0-1200 rpm and heat with a 300 Watt thermostatically controlled element. The stirrer has a stainless steel top and comes with PTFE coated magnets ranging from 10-50mm in 5mm increments, with two of each size included as accessories.
Sterliser, autoclave
Sterliser, autoclavehydrologyproject0This document provides specifications for a sterilizer autoclave. The autoclave is 0.3 x 0.5 meters in size, made of stainless steel inside and lid with an enameled outside. It operates at a working pressure of 1 bar with a maximum pressure of 1.5 bars. Accessories include a pressure gauge, steam release cock, safety valve, perforated aluminum basket, water level indicator, and lifting arrangement. The autoclave is powered by 220 VAC at 47-53 Hz and uses approximately 2500 Watts.
Stabiliser (cvt)
Stabiliser (cvt)hydrologyproject0This document provides specifications for a stabiliser (constant voltage transformer) used to protect sensitive instruments. The stabiliser is a ferro magnetic resonance type that maintains an output of 220 VAC ± 2% from an input of 170-270 VAC at 50 Hz. It has a capacity of 1-3 kVA depending on the instruments, is more than 85% efficient, and includes input/output voltage meters.
Specification totaln kjeldahl
Specification totaln kjeldahlhydrologyproject0The document describes the specifications for a total Kjeldahl nitrogen analyzer system. The system consists of a digestion unit, scrubber unit, and distillation unit. The digestion unit has electrically heated blocks capable of temperatures from 45-450°C and can accommodate at least six 200ml digestion tubes. The scrubber unit is oil-free and collects condensate and acid fumes. The distillation unit has a borosilicate glass steam generator and pump for alkali dispensing. The system requires quality certificates and accessories including spare parts for two years of use.
Specification spectrophotometervisible
Specification spectrophotometervisiblehydrologyproject0This document provides specifications for a spectrophotometer used in a laboratory, including a spectral bandwidth of 2 nm or better, a range of 340 to 950 nm, and an accuracy better than 1 nm. It can measure transmittance, absorbance, and concentration, with a range of 0.00 to 200.0 for transmittance and -0.30 to 3.00 for absorbance. Accessories include square glass cuvettes, an operation manual, dust cover, and power cable. Consumables are also included for two years of operation.
Specification uv spectrophotometer
Specification uv spectrophotometerhydrologyproject0The document describes the specifications for a UV-Visible Spectrophotometer, including its optical system, wavelength range and readability, photometric readout range and accuracy, noise level, data interval, drift, and cell holder. It also lists the required accessories, including cuvettes, manuals, a computer, printer, and consumables for two years of operation. Additional features noted are the storage of spectra and methods, multiple analysis modes, and software for water and environmental analysis.
Specifications aas
Specifications aashydrologyproject0The document describes the specifications for an atomic absorption spectrophotometer used to analyze trace metals and other elements in water and sediment samples. Key features include the ability to measure multiple elements rapidly from a single sample using 4 or more lamp positions. It must be PC-controlled with automatic wavelength selection and calibration. Safety features automatically shut down gases if a flame is not detected. The system includes an integrated flame and graphite furnace with autosampler capable of analyzing up to 50 samples per hour. Required accessories include lamps, gases, regulators, and a 2-year supply of recommended consumables.
Ad
Water bath, bacteriological
- 1. 40.044 WATER BATH, BACTERIOLOGICAL Approval Date: January 2008 Version: 2 Purpose • For incubation of culture tubes in coliform analysis Specifications inner size approximately 0.4 x 0.3 x 0.15 m (l x w x d) material stainless steel inside, stove enameled outside temperature range ambient to 50°C, thermostatically controlled accuracy ±0.1°C power supply 220 VAC ±25%, 47 to 53 Hz Accessories • mercury filled thermometer having 0.1o C graduation Features • double wall, highly insulated • dome lid to accommodate test tubes in vertical position • pilot lamp for thermostat operation • thermometer access hole to display inside water temperature Equipment Specification: WATER BATH, BACTERIOLOGICAL Version 2 40.044-1/1